Ford E250 recalls by model year

Reported: 1975-03-04 (March 4, 1975) · Model years: 1975

Reported: 1975-03-04 (March 4, 1975) · Model years: 1975

Reported: 1975-05-29 (May 29, 1975) · Model years: 1975

Reported: 1975-07-17 (July 17, 1975) · Model years: 1975

Reported: 1976-10-18 (October 18, 1976) · Model years: 1976

Reported: 1977-09-23 (September 23, 1977) · Model years: 1977, 1978

SOME OF THE INVOLVED VEHICLES MAY HAVE DEFECTIVE CARBURETORS IN WHICH, UNDER CERTAIN CIRCUMSTANCES, THE SECONDARY THROTTLE PLATES MAY STICK OPEN.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE CARBURETOR AT NO CHARGE TO OWNER.

Reported: 1977-10-25 (October 25, 1977) · Model years: 1978

ON THE INVOLVED VEHICLES, THE PARK ACTUATION SUPPORT PLATES ARE DEFECTIVE DUE TO THEIR SUSCEPTIBILITY TO CRACKING DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. AS A RESULT, FRAGMENTS FROM A BROKEN PLATE CAN BECOME LODGED IN THE TRANSMISSION PARKING PAWL MECHANISM. THIS COULD PREVENT THE TRANSMISSION PARKING PAWL FROM ENGAGING WHEN THE SELECTOR LEVER IS PLACED IN THE "PARK" POSITION, OR PREVENT THE PAWL FROM BEING DISENGAGED FROM THE PARK GEAR.

Remedy: THE DEALER WILL REPLACE THE PARK ACTUATION CAM SUPPORT PLATES, FREE OF CHARGE, ON ALL AFFECTED VEHICLES.

Reported: 1977-10-25 (October 25, 1977) · Model years: 1978

ON THE INVOLVED VEHICLES, THE STEERING TIE ROD AND LINK ASSEMBLIES WITH ADJUSTING SLEEVE CLAMPS MAY HAVE BEEN IMPROPERLY MANUFACTURED. THE CLAMPS CONTAIN A SHARP DIE MARK WHICH COULD CAUSE THE CLAMP TO FRACTURE WHEN THE CLAMP BOLT IS TIGHTENED TO SPECIFICATIONS. THE CLAMP COULD BREAK AND CAUSE SEPARATION OF THE TIE ROD ADJUSTING SLEEVES.

Remedy: THE DEALER WILL REPLACE THE STEERING TIE ROD ADJUSTING SLEEVE AND CLAMP ASSEMBLY, FREE OF CHARGE, ON ALL AFFECTED VEHICLES.

Reported: 1977-11-15 (November 15, 1977) · Model years: 1978

ON THE INVOLVED VEHICLES, LEAKAGE MAY OCCUR AT THE THREADED CARBURETOR-TO-FUEL FILTER CONNECTION ON THE SUSPECT CARBURETORS. THIS IS DUE TO AN IMPROPERLY MACHINED CARBURETOR FUEL INLET CONNECTION.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, WILL REPLACE THE CARBURETOR WITHOUT CHARGE TO OWNER.

Reported: 1978-02-16 (February 16, 1978) · Model years: 1978

THE SHIFT SELECTOR REACTION SPRINGS MAY BE DEFORMED AS A RESULT OF IMPROPER INSTALLATION OF SELECTOR LEVERS DURING COLUMN BUILDUP. THUS THE LEVER MAY NOT BE ABLE TO BE MOVED INTO THE INSERT DETENTS LOCATED IN THE STEERING COLUMN ASSEMBLY. THIS COULD PREVENT THE "PARK" GEAR FROM BEING ENGAGED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE SHIFT SELECTOR REACTION SPRING WITHOUT CHARGE TO OWNER.

Reported: 1978-10-05 (October 5, 1978) · Model years: 1979

ON THE INVOLVED VEHICLES, THE POTENTIAL EXISTS FOR THE OUTBOARD SEAT BELTS TO BECOME TRAPPED IN THE SEAT-BED PIVOTING MECHANISM. SHOULD THE BELT BECOME TRAPPED IN THE MECHANISM WHEN THE SEAT IS CONVERTED TO A BED, THE BELT MAY BECOME CUT OR FRAYED.

Remedy: THE DEALER WILL INSTALL SEAT BELT SHIELDS ON THE FOLDING SEAT/BED PIVOTING MECHANISM AND REPLACE THE OUTBOARD SEAT BELT ASSEMBLIES IF DAMAGED, FREE OF CHARGE.

Reported: 1979-05-15 (May 15, 1979) · Model years: 1979

THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.

Remedy: DEALER WILL REPLACE THE SUSPECT BRAKE RETAINING PIN.

Reported: 1979-06-19 (June 19, 1979) · Model years: 1979

THE INCORRECTLY INSTALLED LEFT FRONT BRAKE HOSES MAY ALLOW FOR CONTACT BETWEEN THE FRONT BRAKE HOSES AND THE FRONT TIRES WHEN THE FRONT WHEELS ARE IN FULL RIGHT OR LEFT TURN POSITIONS. IF CONTACT IS MADE, THE HOSE COULD WEAR AND ALLOW BRAKE FLUID TO LEAK OUT.

Remedy: THE DEALER WILL INSPECT FRONT BRAKE HOSES AND REPLACE THOSE LACKING THE PROPER CLEARANCE WITH CURRENT PRODUCTION HOSES, WITHOUT CHARGE TO OWNER.

Reported: 1979-06-19 (June 19, 1979) · Model years: 1979

CERTAIN VEHICLES MAY NOT CONTAIN THE SPECIFIED BODY MOUNTED HEAT SHIELDS. THIS COULD CAUSE HIGH FLOOR PAN TEMPERATURES WHEN THE ENGINE IS IDLED FOR EXTENDED PERIODS OF TIME. FOULED SPARK PLUGS OR OTHER ENGINE CONDITIONS COULD FURTHER INCREASE EXHAUST TEMPERATURES.

Remedy: THE DEALER WILL INSTALL THE NECESSARY FRAME MOUNTED HEAT SHIELD, IF MISSING.

Reported: 1980-07-14 (July 14, 1980) · Model years: 1980

DUE TO COMPUTER INPUT ERROR WHICH RESULTED IN AN INCORRECT BUILD SCHEDULE, SOME VEHICLES WERE SHIPPED WITHOUT THE REQUIRED EXHAUST SYSTEM HEAT SHIELDS. WHEN THE VEHICLE IS IDLED OVER AN EXTENDED PERIOD OF TIME, A MISSING EXHAUST HEAT SHIELD MAY RESULT IN DANGEROUSLY HIGH FLOOR PAN TEMPERATURES.

Remedy: DEALER WILL INSTALL FRAME-MOUNTING HEAT SHIELDS WITHOUT CHARGE TO OWNER.

Reported: 1982-01-13 (January 13, 1982) · Model years: 1982

ON SOME OF THE INVOLVED VEHICLES, THE SHIFT ROD IN THE TRANSMISSION MAY NOT BE PROPERLY SEATED IN THE RETENTION GROMMET OF THE STEERING COLUMN SHIFT LEVER ASSEMBLY. IF THE SHIFT ROD WERE TO DISENGAGE, THE DRIVER COULD NOT SELECT THE PROPER TRANSMISSION FUNCTION WHICH WOULD CREATE THE POTENTIAL FOR UNEXPECTED MOVEMENT OF THE VEHICLE.

Remedy: DEALER WILL INSPECT THE SHIFT ROD ATTACHMENT AND MAKE SURE IT IS PROPERLY SEATED AT NO COST TO OWNER.

Reported: 1982-10-26 (October 26, 1982) · Model years: 1982, 1983

ON CERTAIN VEHICLES, THE LOCK WEDGES USED TO SECURE THE AXLE BEARING NUTS TO THE AXLE HOUSING MAY FALL OUT OF POSITION, ALLOWING THE NUT TO LOOSEN. THE NUT ON THE LEFT SIDE MAY FALL OFF, ALLOWING MOVEMENT OF THE AXLE SHAFT.

Remedy: THE DEALER WILL REPLACE DEFECTIVE LOCK WEDGES WITH AN IMPROVED VERSION. WHEEL BEARINGS WILL BE INSPECTED AND ADJUSTED OR REPLACED, IF NECESSARY.

Reported: 1982-12-13 (December 13, 1982) · Model years: 1983

SOME OF THE INVOLVED VEHICLES MAY HAVE A DIODE IN THE ELECTRICAL FUEL PUMP CIRCUIT THAT MAY SHORT DURING ENGINE STARTING DUE TO INADEQUATE CAPACITY TO WITHSTAND CURRENT DRAW. A SHORT CIRCUIT WOULD RESULT IN NORMAL ENGINE STARTING, BUT THE PUMP WILL NOT CONTINUE TO SUPPLY THE ENGINE WITH FUEL.

Remedy: THE DEALER WILL REPLACE DEFECTIVE ELEMENT IN THE ELECTRICAL FUEL PUMP CIRCUIT WITH A NEW RELAY FEED WIRING ASSEMBLY WHICH CONTAINS A LARGER CAPACITY DIODE, FREE OF CHARGE.

Reported: 1985-05-14 (May 14, 1985) · Model years: 1983, 1984, 1985

WHEN FRONTALLY IMPACTED INTO A FIXED BARRIER AT 30 MPH, AS SPECIFIED IN FEDERAL MOTOR VEHICLE SAFETY STANDARD (FMVSS) NO. 301, THE LEFT FRAME RAILS OF SUCH VEHICLES MAY DISPLACE INBOARD, PINCHING THE FUEL/WATER SEPARATOR CANISTER BETWEEN THE FRAME RAIL AND ENGINE SUFFICIENTLY TO DISPLACE THE FUEL/WATER SEPARATOR DRAIN ROD, ALLOWING THE CONTENTS OF THE CANISTER TO DRAIN. CONSEQUENCE OF DEFECT: FUEL LEAK DURING OR AFTER A CRASH INCREASES THE POSSIBILITY OF A FIRE.

Remedy: INSTALL A CANISTER SHIELD, A REVISED DESIGN DRAIN ROD SHIELD, AND MODIFY FUEL/WATER SEPARATOR MOUNTING BRACKET.

Reported: 1987-09-09 (September 9, 1987) · Model years: 1983, 1984, 1985, 1986, 1987

VEHICLES ARE SUBJECT TO EXCESSIVE UNDERHOOD TEMPERATURES AND FUEL SYSTEM PRESSURES IN SEVERE DUTY APPLICATIONS.

Consequence: THIS CREATES POTENTIAL FOR FUEL EXPULSION FROM THE FUELFILLER PIPE WHICH IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN AFIRE.

Remedy: INSTALL MODIFICATION KITS TO MINIMIZE POSSIBILITY OF FUEL EXPULSION AND TO SHIELD UNDERBODY COMPONENTS FROM EXHAUST SYSTEM HEAT.

Reported: 1988-08-09 (August 9, 1988) · Model years: 1983, 1984, 1985, 1986, 1987

EXTREME OPERATING CONDITIONS COULD CAUSE PREMATURE DETERIORATION OF THE ENGINE COMPARTMENT HEATER HOSES OR ENGINE BYPASS HOSES.

Consequence: ENGINE COOLANT COULD DISCHARGE ONTO THE ENGINE AND ITSEXHAUST MANIFOLD CREATING THE POTENTIAL FOR A FIRE DUE TO THE HIGH ENGINEEXHAUST MANIFOLD TEMPERATURES.

Remedy: REPLACE HOSES AND RADIATOR CAPS; INSTALL HIGH HEAT RESISTANCE ALUMINIZED STAINLESS STEEL MUFFLERS.

Reported: 1984-01-07 (January 7, 1984) · Model years: 1984

SOME VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED WHEELS. THE WELDS SECURING THE CENTER SECTIONS TO THE RIMS MAY CRACK FROM FATIGUE.

Remedy: AFFECTED WHEELS WILL BE REPLACED.

Reported: 1984-10-02 (October 2, 1984) · Model years: 1984

THE SECONDARY THROTTLE SHAFT MAY, WITH ACCUMULATED MILEAGE, BECOME CONTAMINATED AND MAY STICK IN A PARTIALLY OPEN POSITION WHILE DRIVING.

Consequence: CONSEQUENCE OF DEFECT: THIS STICKING COULD RESULT IN A FASTER SPEED THAN INTENDED, POSSIBLY RESUTLING IN AN ACCIDENT.

Remedy: THE PRIMARY TO SECONDARY THROTTLE CLOSURE LINK ON THE CARBURETOR WILL BE REPLACED FREE OF CHARGE.

Reported: 1986-12-30 (December 30, 1986) · Model years: 1985, 1986

RUBBER THAT ENCASES BALL STUD AND SOCKET JOINT (CONNECTS STEERING DRAG LINK AND PITMAN ARM) MAY DETERIORATE AND CAUSE METAL TO METAL CONTACT. CONSEQUENCE OF DEFECT: COMPLETE SEPARATION OF THE DRAG LINK TO PITMAN ARM CONNECTION COULD OCCUR RESULTING IN LOSS OF STEERING CONTROL.

Remedy: INSTALL NEW DRAG LINK ASSEMBLIES WITH STEEL BALL AND SOCKET JOINTS AT THE PITMAN ARM CONNECTIONS.

Reported: 1990-06-01 (June 1, 1990) · Model years: 1989, 1990

UNDER CERTAIN CONDITIONS, THE SNAP RING THAT LOCATES THE PARK GEAR ON THE OUTPUT SHAFT OF THE TRANSMISSION MAY FRACTURE.

Consequence: WHEN THE GEAR IS PLACED IN PARK, THE PARK GEAR WOULD NOTENGAGE, ALLOWING THE TRUCK TO ROLL FREELY IF THE PARKING BRAKE IS NOT PROPERLYSET. THIS COULD RESULT IN AN ACCIDENT.

Remedy: INSTALL IMPROVED SNAP RING AND REVISED TRANSMISSION EXTENSION HOUSING.

Reported: 1991-09-04 (September 4, 1991) · Model years: 1989, 1990

THE DUAL FUEL TANK SELECTOR VALVE MAY MALFUNCTION AND CAUSE AN OVERFILL CONDITION IN ONE OF THE FUEL TANKS, RESULTING IN AN OVERFLOW OF FUEL PAST THE FILLER CAP.

Consequence: THE OVERFLOW OF FUEL PAST THE FILLER CAP CAUSES A FUELLEAKAGE, WHICH CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.

Remedy: REPLACE THE DUAL FUEL TANK SELECTOR VALVE.

Reported: 2004-11-26 (November 26, 2004) · Model years: 1997, 1998, 1999, 2000

ON CERTAIN VANS EQUIPPED WITH SURE-LOK WHEELCHAIR SECUREMENT SYSTEMS, THE SPROCKET TEETH OF THE RETRACTOR ASSEMBLY IS OUT OF ALIGNMENT.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE WHEELCHAIR MAY NOT BE ADEQUATELY SECURED POSSIBLY RESULTING IN INJURIES TO A WHEELCHAIR OCCUPANT.

Remedy: DEALERS WILL INSPECT AND REPLACE THE WHEELCHAIR SECUREMENT RETRACTORS AS NECESSARY. SURE-LOK WILL HANDLE THE REPAIRS FOR THIS CAMPAIGN. OWNERS SHOULD CONTACT SURE-LOCK AT 1-908-231-1804 OR MOBILITYWORKS AT 1-800-769-8267.

Reported: 2004-12-15 (December 15, 2004) · Model years: 2002, 2003

ON CERTAIN VANS BUILT ON FORD E250/E350 CHASSIS AND EQUIPPED WITH SURE-LOK WHEELCHAIR SECUREMENT SYSTEMS, THE SPROCKET TEETH OF THE RETRACTOR ASSEMBLY IS OUT OF ALIGNMENT.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE WHEELCHAIR MAY NOT BE ADEQUATELY SECURED POSSIBLY RESULTING IN INJURIES TO A WHEELCHAIR OCCUPANT.

Remedy: DEALERS WILL INSPECT AND REPLACE THE WHEELCHAIR SECUREMENT RETRACTORS AS NECESSARY. SURE-LOK IS CONDUCTING THE OWNER NOTIFICATION AND REMEDY FOR THIS CAMPAIGN. OWNERS SHOULD CONTACT SURE-LOCK AT 1-908-231-1804 OR ACCUBUILT AT 419-222-1501.

Reported: 2008-10-06 (October 6, 2008) · Model years: 2005

MOBILITYWORKS IS RECALLING 133 MY 2005-2006 FORD E250, MY 2000, 2004-2006 E350, MY 2000, 2005 E450, MY 2005-2006 GMC 2500, GMC 3500, AND MY 2006 DODGE 2500 VANS EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE LIFTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, "PLATFORM LIFT SYSTEMS FOR MOTOR VEHICLES." THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT.

Consequence: A LIFT OCCUPANT CAN BE INJURED SHOULD THE LIFT BEGIN TO STOW UNINTENTIONALLY.

Remedy: MOBILITYWORKS IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E097). OWNERS MAY CONTACT RICON AT 1-818-267-3000 OR MOBILITYWORKS AT 1-800-769-8267.

Reported: 2014-10-10 (October 10, 2014) · Model years: 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013

Mobility Works (WMK Inc.) is recalling certain model year 2006-2014 Ford E150, E250, and E350 vans modified by Mobility Works to be equipped with certain model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation. The platform side plate of the affected wheelchair lifts may crack.

Consequence: If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. When the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.

Remedy: Mobility Works will notify owners, and Ricon will supply supplemental platform support bumpers. Any platform that has already started cracking will be replaced, free of charge. The recall began on November 10, 2014. Owners may contact Mobility Works customer service at 1-800-769-8267 or Ricon customer service at 1-800-322-2884.