| Electrical System | 150.0%ODI 10653583 · 13,269 miI WAS DRIVING EAST ON I10 WHEN THE CHECK ENGINE LIGHT CAME ON. I THEN NOTICED THE DASH PANEL GOING IN ALL DIFFERENT DIRECTIONS. THE ERROR CODE CAME UP AS J1939. TALKING WITH WINNEBAGO AND CUMMINGS ENGINE THEY BOTH STATED THIS WAS A CHASSIS PROBLEM AND CONTACT FREIGHTLINER. I CALLED THEM IN ORLANDO FLORIDA AND THEY STATED THEY WERE AWARE OF SOME PROBLEM WITH THE DASH INSTRUMENT PANEL OR ASSOCIATED ELECTRICAL CONTROL BOARD. THEY ALSO STATED THERE COULD BE AN ELECTRICAL SHORT IN THE WIRING HARNESS. I DID NOT HAVE AN ACCIDENT AND DID NOT LIKE… Look up ODI 10653583 at NHTSA ↗ | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 150.0%ODI 11488502My problems are the same as what is listed in recall 21V-00H. I have experienced a loss of rear turn singles, brake lights not working, wind shield wipers going off no mater of switch position. The lack of rear lighting can in increase the possibility of a crash . Look up ODI 11488502 at NHTSA ↗ | 00.0%No examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. |
|---|
| Exterior Lighting | 00.0%No examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 2100.0%ODI 11488502My problems are the same as what is listed in recall 21V-00H. I have experienced a loss of rear turn singles, brake lights not working, wind shield wipers going off no mater of switch position. The lack of rear lighting can in increase the possibility of a crash . Look up ODI 11488502 at NHTSA ↗ | 00.0%No examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. |
|---|
| Fuel/Propulsion System | 150.0%ODI 10850759 · 544,000 miTRUCK FIRE WITH COMPLETE DESTRUCTION DUE TO HIGH PRESSURE FUEL LINES FROM PUMP TO FUEL RAIL. P CLIPS ALLEGEDLY COMPROMISED FUEL LINE. DAIMLER HAS HAD A RECALL BUT THIS IS A DESIGN DEFECT THAT NEEDS INVESTIGATED AS THE "FIX" IS NO FIX AND FIRES CONTINUE TO OCCUR. Look up ODI 10850759 at NHTSA ↗ | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 00.0%No examples available for this selection. | 1100.0%ODI 11514515The drive shaft fwd carrier bearing was missing 2 of the 3 bolt that hold it to the cross member. Being held with one bolt change the center line of the drive shaft moving towards the driver's side of the truck this resulted the the drive shaft rubbing on a air tank hanger. I do have pictures. It looks like the missing bolts where never installed. Look up ODI 11514515 at NHTSA ↗ | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. |
|---|
| Power Train | 00.0%No examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 00.0%No examples available for this selection. | 1100.0%ODI 11514515The drive shaft fwd carrier bearing was missing 2 of the 3 bolt that hold it to the cross member. Being held with one bolt change the center line of the drive shaft moving towards the driver's side of the truck this resulted the the drive shaft rubbing on a air tank hanger. I do have pictures. It looks like the missing bolts where never installed. Look up ODI 11514515 at NHTSA ↗ | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. |
|---|
| Service Brakes | 00.0%No examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 00.0%No examples available for this selection. | 1100.0%ODI 11514515The drive shaft fwd carrier bearing was missing 2 of the 3 bolt that hold it to the cross member. Being held with one bolt change the center line of the drive shaft moving towards the driver's side of the truck this resulted the the drive shaft rubbing on a air tank hanger. I do have pictures. It looks like the missing bolts where never installed. Look up ODI 11514515 at NHTSA ↗ | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. | 0UnavailableNo examples available for this selection. |
|---|