Gmc C25 recalls by model year

Reported: 1972-10-02 (October 2, 1972) · Model years: 1972

Reported: 1978-08-15 (August 15, 1978) · Model years: 1978

THE NUT ON THE CARRIER SUPPORT BOLT ASSEMBLY MAY BREAK WHICH WOULD ALLOW THE ENTIRE WHEEL AND TIRE ASSEMBLY TO SEPARATE FROM THE VEHICLE.

Remedy: DEALER WILL REPLACE THE TIRE AND WHEEL CARRIER BOLT ASSEMBLY AT NO CHARGE.

Reported: 1986-09-19 (September 19, 1986) · Model years: 1986

THE PUSH PULL HEADLIGHT SWITCH MAY HAVE ELECTRICAL CONTACTS WHICH ALLOW AN INTERMITTENT HEADLIGHT CIRCUIT CAUSING HEADLIGHT TO FLICKER OR SUDDENLY GO OUT. CONSEQUENCE OF DEFECT: SUDDEN LOSS OF THE HEADLIGHTS UNDER SEVERE WEATHER OR NIGHTTIME DRIVING CONDITIONS COULD REDUCE DRIVER VISIBILITY WHICH MIGHT RESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.

Remedy: REPLACE HEADLIGHT SWITCH AS NECESSARY.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

CRUISE CONTROL CABLE LOCK MECHANISM MAY SELF DISENGAGE CAUSING ERRATIC OPERATION OR THROTTLE NOT RETURNING TO IDLE.

Consequence: ENGINE SPEED WOULD NOT DECREASE; LOSS OF ACCELERATORCONTROL COULD RESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A CLAMP AROUND THE LOCK TAB OF CRUISE CONTROL.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

ONE OR BOTH OF OUTER TIE ROD NUTS MAY BE LOOSE AND NOT CRIMPED.

Consequence: LOSS OF ONE OR BOTH NUTS COULD LEAD TO TIE RODDISENGAGING FROM STEERING KNUCKLE RESULTING IN POSSIBLE LOSS OF STEERINGCONTROL AND POSSIBLY A CRASH.

Remedy: REPLACE TIE ROD AND KNUCKLE AND SET TOE-IN.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

TRUCKS MAY HAVE CRACKED OR BROKEN DOOR STRIKER NUTS, WHICH DO NOT CONFORM TO FMVSS 206.

Consequence: IN A COLLISION, CRACKED OR BROKEN STRIKER NUT COULDALLOW DOOR TO OPEN UNEXPECTEDLY AND POSSIBLY CAUSE INJURY TO OCCUPANTS.

Remedy: REPLACE EXISTING DOOR STRIKER NUTS.

Reported: 1987-09-01 (September 1, 1987) · Model years: 1988

RIGHT AND LEFT HAND BRAKE HOSE MAY CONTACT THE WHEEL OR TIRE IN A FULL TURN.

Consequence: IF THE HOSE MAKES CONTACT WITH THE WHEEL OR TIRE IT WILLEVENTUALLY WEAR THE HOSE TO A POINT OF RUPTURE, RESULTING IN A LOSS OF THEFRONT BRAKES. LOSS OF FRONT BRAKES WOULD INCREASE THE STOPPING DISTANCE WHENMINIMUM TIME IS REQUIRED AND COULD RESULT IN A VEHICLE CRASH.

Remedy: INSTALL NEW REPOSITIONING BRACKETS FOR THE FRONT BRAKE HOSES.

Reported: 1989-05-15 (May 15, 1989) · Model years: 1989

THERE MAY BE BELOW SPECIFIED TORQUE ON THE TRAILER HITCH ATTACHING FASTENERS, ALLOWING THE TRAILER HITCH TO MOVE UNDER TOWING LOADS.

Consequence: FASTENERS COULD FAIL; IF THIS OCCURS WHILE TRAILERIS BEING PULLED, HITCH AND TRAILER COULD SEPARATE AND A VEHICLE CRASH COULDOCCUR WITHOUT PRIOR WARNING.

Remedy: CORRECT TORQUE IN TRAILER HITCH FASTENERS TO PREVENT TRAILER SEPARATION.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1990-06-04 (June 4, 1990) · Model years: 1990

LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.

Consequence: THIS COULD CAUSE LOSS OF BRAKING ACTIVITY THAT COULDRESULT IN A TRUCK CRASH WITHOUT PRIOR WARNING.

Remedy: RETORQUE BRAKE PEDAL PIVOT BOLTS TO SPECIFICATIONS TO PREVENT LOOSENING.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1992, 1993

VEHICLES ALTERED BY PAS, INC. HAVE COMPRESSED NATURAL GAS FUEL TANKS THAT CAN DEVELOP STRESS CORROSION, WHICH CRACK THE E-GLASS WRAPPING. THIS STRESS CORROSION CRACKING CAN LEAD TO TANK RUPTURES.

Consequence: IF THE TANK RUPTURES, PERSONAL INJURY TO INDIVIDUALS IN OR NEAR THE VEHICLE MAY OCCUR.

Remedy: GM IS OFFERING TO EXCHANGE THESE VEHICLES WITH A COMPARABLY EQUIPPED 1994 GASOLINE 1/2 OR 3/4 TON GM PICKUP. IF THE OWNER CHOOSES NOT TO EXCHANGE THE NATURAL GAS VEHICLE, GM WILL REPURCHASE THE VEHICLE.

Reported: 1999-05-20 (May 20, 1999) · Model years: 1992

VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.

Reported: 1995-12-21 (December 21, 1995) · Model years: 1993, 1994

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1993-09-15 (September 15, 1993) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993) · Model years: 1994

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1994

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1994-10-26 (October 26, 1994) · Model years: 1994

THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.

Remedy: DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

Consequence: IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

Remedy: DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

Reported: 1999-02-05 (February 5, 1999) · Model years: 1994

VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

Consequence: THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.

Reported: 1995-02-16 (February 16, 1995) · Model years: 1995

DUE TO A THIN CASE CASTING, AN EXTERNAL TRANSMISSION LEAK CAN OCCUR.

Consequence: THIS CONDITION CAN CAUSE TRANSMISSION OIL TO SPRAYONTO THE EXHAUST SYSTEM AND RESULT IN A POSSIBLE VEHICLE FIRE.

Remedy: DEALERS WILL INSPECT THE TRANSMISSION CASE ASSEMBLY FOR THE INVOLVED CASE CASTING. IF THE ASSEMBLY IS INVOLVED, THE TRANSMISSION WILL BE REPLACED.

Reported: 1996-01-02 (January 2, 1996) · Model years: 1995

THE STEERING COLUMN UPPER INTERMEDIATE-SHAFT NUT MAY NOT BE TORQUED TO PROPER SPECIFICATIONS. THE NUT COULD LOOSEN AND DETACH ALLOWING THE THROUGH-BOLT THAT SECURES THE UPPER INTERMEDIATE-SHAFT TO THE LOWER STEERING COLUMN SHAFT JOINT TO FALL OUT.

Consequence: THIS LOOSE ENGAGEMENT CAN PROVIDE NOTICEABLE NOISE AND ABNORMAL STEERING FEELING TO THE DRIVER AND, IF LEFT UNATTENDED, THE STEERING SHAFTS CAN SEPARATE RESULTING IN A LOSS OF STEERING CONTROL.

Remedy: DEALERS WILL TORQUE THE SUSPECT FASTENERS TO THE PROPER SPECIFICATIONS.

Reported: 1996-04-04 (April 4, 1996) · Model years: 1995, 1996

THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, "ACCELERATOR CONTROL SYSTEMS."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE ENGINE SPEED MAY NOT RETURN TO IDLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT FOR ADEQUATE THROTTLE CABLE TO DASH MAT CLEARANCE, AND IF THERE IS INSUFFICIENT CLEARANCE, CUT OUT A PORTION OF THE DASH MAT TO PROVIDE PROPER CLEARANCE.

Reported: 1997-03-07 (March 7, 1997) · Model years: 1995, 1996

VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.

Consequence: THIS PINCHING CAN CUT THE HAND OR POSSIBLY SEVER THE FINGER(S) WITHOUT PRIOR WARNING.

Remedy: DEALERS WILL INSTALL A PROTECTOR COVER OVER THE RECLINER MECHANISM.

Reported: 1995-12-28 (December 28, 1995) · Model years: 1996

CERTAIN TRUCKS HAVE FUEL RAIL ASSEMBLIES WITH AN IMPROPERLY CRIMPED END RETAINER CLIP THAT RESULTS IN A FUEL LEAK.

Consequence: IF FUEL LEAKAGE OCCURS AND AN IGNITION SOURCE IS PRESENT, AN ENGINE COMPARTMENT FIRE COULD OCCUR.

Remedy: DEALERS WILL INSPECT THE FUEL RAIL ASSEMBLY AND REPLACE ANY FUEL RAIL ASSEMBLY WITH A JULIAN DATE CODE OF 95318 THROUGH 95338.

Reported: 1996-05-07 (May 7, 1996) · Model years: 1996

THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.

Consequence: VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.