Gmc K35 recalls by model year

Reported: 1972-10-02 (October 2, 1972) · Model years: 1972

Reported: 1983-03-22 (March 22, 1983) · Model years: 1983

VEHICLES MAY HAVE BEEN ASSEMBLED WITHOUT THE ROOF MARKER LAMPS REQUIRED FOR TRUCKS OF 80 OR MORE INCHES OVERALL WIDTH. VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 108, "LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT".

Remedy: DEALER WILL INSTALL ROOF MARKER LAMPS AT NO CHARGE TO OWNER.

Reported: 1985-02-20 (February 20, 1985) · Model years: 1985

CERTAIN TRUCKS DO NOT COMPLY WITH FMVSS 108, "LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT." THE TRUCKS WERE ASSEMBLED WITHOUT THE ROOF MARKER LAMPS. CONSEQUENCE OF DEFECT: SAFE OPERATION OF THE TRUCKS DURING DARKNESS OR REDUCED VISIBILITY WOULD BE IMPAIRED.

Remedy: INSTALL ROOF MARKER LAMPS.

Reported: 1985-05-01 (May 1, 1985) · Model years: 1985

RIM INFORMATION MAY HAVE BEEN OMITTED ON CERTIFICATION LABEL INSTALLED ON THE LEFT FRONT DOOR. CONSEQUENCE OF DEFECT: THESE TRUCKS DO NOT CONFORM WITH FMVSS 120, TIRE SELECTIONS AND RIMS FOR VEHICLES OTHER THAN PASSENGER CARS.

Remedy: INSTALL NEW CORRECTED LABELS.

Reported: 1985-11-26 (November 26, 1985) · Model years: 1985

THE WHEEL MAY DEVELOP CRACKS BETWEEN THE DISC AND RIM. CONSEQUENCE OF DEFECT: IF THIS OCCURS AND IS NOT NOTICED, THE CRACK COULD INCREASE AROUND THE RIM, RESULTING IN SEPARATION OF THE RIM FROM THE DISC, LOSS OF CONTROL AND AN ACCIDENT MAY OCCUR.

Remedy: REPLACE WHEELS HAVING THE SUSPECTED MANUFACTURING CODE NUMBER.

Reported: 1986-09-19 (September 19, 1986) · Model years: 1986

THE PUSH PULL HEADLIGHT SWITCH MAY HAVE ELECTRICAL CONTACTS WHICH ALLOW AN INTERMITTENT HEADLIGHT CIRCUIT CAUSING HEADLIGHT TO FLICKER OR SUDDENLY GO OUT. CONSEQUENCE OF DEFECT: SUDDEN LOSS OF THE HEADLIGHTS UNDER SEVERE WEATHER OR NIGHTTIME DRIVING CONDITIONS COULD REDUCE DRIVER VISIBILITY WHICH MIGHT RESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.

Remedy: REPLACE HEADLIGHT SWITCH AS NECESSARY.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

CRUISE CONTROL CABLE LOCK MECHANISM MAY SELF DISENGAGE CAUSING ERRATIC OPERATION OR THROTTLE NOT RETURNING TO IDLE.

Consequence: ENGINE SPEED WOULD NOT DECREASE; LOSS OF ACCELERATORCONTROL COULD RESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A CLAMP AROUND THE LOCK TAB OF CRUISE CONTROL.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

TRUCKS MAY HAVE CRACKED OR BROKEN DOOR STRIKER NUTS, WHICH DO NOT CONFORM TO FMVSS 206.

Consequence: IN A COLLISION, CRACKED OR BROKEN STRIKER NUT COULDALLOW DOOR TO OPEN UNEXPECTEDLY AND POSSIBLY CAUSE INJURY TO OCCUPANTS.

Remedy: REPLACE EXISTING DOOR STRIKER NUTS.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

INCORRECT FRONT SHOCK ABSORBER UPPER AND LOWER NUTS COULD LOOSEN.

Consequence: SHOCK ABSORBER COULD DETACH AND COME IN CONTACT WITHFRONT BRAKE HOSE; THIS CONTACT COULD RESULT IN A LEAK IN THE HOSE AND LOSS OFFRONT BRAKES.

Remedy: REPLACE FREE SPINNING NUTS WITH TORQUE NUTS.

Reported: 1989-05-15 (May 15, 1989) · Model years: 1989

THERE MAY BE BELOW SPECIFIED TORQUE ON THE TRAILER HITCH ATTACHING FASTENERS, ALLOWING THE TRAILER HITCH TO MOVE UNDER TOWING LOADS.

Consequence: FASTENERS COULD FAIL; IF THIS OCCURS WHILE TRAILERIS BEING PULLED, HITCH AND TRAILER COULD SEPARATE AND A VEHICLE CRASH COULDOCCUR WITHOUT PRIOR WARNING.

Remedy: CORRECT TORQUE IN TRAILER HITCH FASTENERS TO PREVENT TRAILER SEPARATION.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1990-06-04 (June 4, 1990) · Model years: 1990

LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.

Consequence: THIS COULD CAUSE LOSS OF BRAKING ACTIVITY THAT COULDRESULT IN A TRUCK CRASH WITHOUT PRIOR WARNING.

Remedy: RETORQUE BRAKE PEDAL PIVOT BOLTS TO SPECIFICATIONS TO PREVENT LOOSENING.

Reported: 1999-05-20 (May 20, 1999) · Model years: 1992

VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.

Reported: 1993-09-27 (September 27, 1993) · Model years: 1993

THE REAR BENCH SEAT DOES NOT MEET THE LOAD REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS," BECAUSE THE MANUAL LATCH MECHANISM ON THE FOLDING FULL BENCH REAR SEAT WAS ATTACHED TO THE BACK FRAME LOWER CROSS TUBE WITH DOMED HEAD STEEL RIVETS INSTEAD OF THE BOLTS SPECIFIED.

Remedy: THE RIVETS MUST BE REPLACED WITH THE CORRECT BOLTS.

Reported: 1995-12-21 (December 21, 1995) · Model years: 1993, 1994

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1993-09-15 (September 15, 1993) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993) · Model years: 1994

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1994

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1995-02-16 (February 16, 1995) · Model years: 1995

DUE TO A THIN CASE CASTING, AN EXTERNAL TRANSMISSION LEAK CAN OCCUR.

Consequence: THIS CONDITION CAN CAUSE TRANSMISSION OIL TO SPRAYONTO THE EXHAUST SYSTEM AND RESULT IN A POSSIBLE VEHICLE FIRE.

Remedy: DEALERS WILL INSPECT THE TRANSMISSION CASE ASSEMBLY FOR THE INVOLVED CASE CASTING. IF THE ASSEMBLY IS INVOLVED, THE TRANSMISSION WILL BE REPLACED.

Reported: 1996-07-01 (July 1, 1996) · Model years: 1995, 1996

THESE TIRES HAVE BEAD DAMAGE WHICH OCCURED DURING TIRE MOUNTING.

Consequence: THIS DAMAGE TO THE TIRE REINFORCING STRUCTURE IN THE BEAD "TOE" AREA CAUSES A BULGE IN THE SIDEWALL AFTER THE TIRE IS INFLATED. THIS CONDITION WILL RESULT IN A SLOW AIR LOSS CAUSING THE TIRE TO GO FLAT. HOWEVER, IT IS POSSIBLE FOR THE DAMAGE TO RESULT IN A RAPID AIR LOSS CAUSING INJURIES TO ANYONE IF THEY WERE HANDLING THE TIRE WHEN THIS OCCURRED.

Remedy: DEALERS WILL DEMOUNT EACH TIRE AND INSPECT FOR BEAD DAMAGE. IF BEAD DAMAGE IS FOUND, THE TIRE WILL BE REPLACED.

Reported: 1996-05-07 (May 7, 1996) · Model years: 1996

THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.

Consequence: VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.