International Harvester 9200 recalls by model year

Reported: 1995-05-24 (May 24, 1995) · Model years: 1994, 1995

THE SWIVEL SEAT ASSEMBLY ATTACHMENTS BETWEEN THE UPPER AND LOWER PORTIONS ARE INADEQUATE TO INSURE THAT THE ASSEMBLY WILL STAY TOGETHER DURING NORMAL USE. VIBRATION CAN CAUSE THE ATTACHING BOLTS TO WORK LOOSE AND FALL OUT.

Consequence: SHOULD THE BOLTS FALL OUT, THE SEAT SWIVEL ASSEMBLY WOULD SEPARATE. IF THIS SHOULD HAPPEN WHILE THE VEHICLE IS IN MOTION, IT COULD CAUSE THE OPERATOR TO LOSE CONTROL OF THE VEHICLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSTALL A NEW RE-DESIGNED SWIVEL MOUNT/STOP RING, A SPACER AND NEW LONGER MOUNTING BOLTS.

Reported: 1995-09-25 (September 25, 1995) · Model years: 1995, 1996

STRAPS HOLDING THE SLEEPER UPPER BUNK IN THE RAISED POSITION CAN RELEASE WITHOUT WARNING.

Consequence: IF THE RESTRAINING STRAP RELEASES SUDDENLY, THE BUNKFALLS WITHOUT WARNING AND CAN STRIKE AN OCCUPANT SITTING IN THE LOWER BUNK CAUSING PERSONAL INJURY.

Remedy: DEALERS WILL MODIFY THE ATTACHMENT OF THE UPPER BUNK RESTRAINING STRAP TO THE UPPER BUNK AND REAR WALL OF THE SLEEPER AND INSTALL A NEW REDESIGNED BUNK RESTRAINING STRAP.

Reported: 2001-02-01 (February 1, 2001) · Model years: 1996, 1997, 1998, 1999, 2000, 2001

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH AIR BRAKE HALDEX AUTOMATIC SLACK ADJUSTERS, LONG STROKE BRAKE CHAMBERS, AND DANA BRAKES. THE AUTOMATIC SLACK ADJUSTER ANCHOR BRACKETS CAN FAIL DUE TO FATIGUE FRACTURE AND COMPLETELY SEPARATE, CAUSING THE SLACK ADJUSTERS TO FUNCTION AS MANUAL SLACK ADJUSTERS.

Consequence: IF THE SUPPORT BRACKET FOR AN AUTOMATIC SLACK ADJUSTER FAILS, THE BRAKES AT THAT WHEEL END WILL NOT AUTOMATICALLY ADJUST. AS THE BRAKE LININGS WEAR, THE VEHICLE WILL HAVE REDUCED BRAKING CAPACITY, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSTALL A NEW BRACKET ON EACH SUSPECT SLACK ADJUSTER. OWNER NOTIFICATION BEGAN FEBRUARY 22, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.

Reported: 2004-02-27 (February 27, 2004) · Model years: 1996, 1997, 1998, 1999, 2000, 2001

ON CERTAIN CONVENTIONAL TRUCKS EQUIPPED WITH PRO-SLEEPER BERTHS, WATER INTRUSION CAN BE FOUND IN THE BUNK CONTROL PANEL AREA AND POOL IN THE TOPS OF THE DOME LIGHT, TV/VCR, AND OR REFRIGERATOR POWER SWITCHES.

Consequence: THE CIRCUIT BOARDS IN THE SWITCHES COULD HEAT UP , POSSIBLY PRODUCE A FLAME OR FIRE, AND CAUSE PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: DEALERS WILL INSTALL A WATER SHIELD OVER THE BACK OF THE ENTIRE BUNK CONTROL PANEL. OWNER NOTIFICATION BEGAN ON JULY 16, 2004. OWNERS SHOULD CONTACT INTERNATIONAL AT 1-800-448-7825.

Reported: 1995-09-14 (September 14, 1995) · Model years: 1996

THE DRIVELINE COULD HAVE LITTLE TORQUE OR NO TORQUE ON THE DRIVELINE NUT THAT RETAINS THE YOKE AT THE CENTER BEARING OR BEARINGS IF THE VEHICLE IS EQUIPPED WITH MULTIPLE CENTER BEARINGS.

Consequence: THE LOW TORQUE CONDITION CAN CAUSE THE DRIVELINE TO SEPARATE RESULTING IN PERSONAL INJURY OR PROPERTY DAMAGE FROM PARTS BEING THROWN FROM THE VEHICLE OR SCATTERED ON THE ROADWAY.

Remedy: DEALERS WILL DISCONNECT THE DRIVELINE AT THE REAR OF THE CENTER BEARING(S), TORQUE THE YOKE NUT AND RECONNECT THE DRIVELINE.

Reported: 1996-08-01 (August 1, 1996) · Model years: 1996

THE EQUALIZING BEAM SHAFT OF THE TANDEM AXLE SUSPENSION WERE MANUFACTURED FROM AS-ROLLED SAE4140 STEEL RATHER THAN THE SPECIFIED ANNEALED SAE4140. THESE SHAFTS CAN FRACTURE INSIDE THE BEAM AT THE TOE OF THE WELD.

Consequence: VEHICLES ARE SUBJECT TO VEHICLE TILT AND POSSIBLE ROLLOVER IN THE EVENT THAT BOTH EQUALIZING BEAMS, ON THE SAME SIDE OF THE VEHICLE, EXPERIENCE A SIMULTANEOUS SHAFT FAILURE. AFFECTED SUSPENSIONS CAN ALSO DROP AND CONTACT THE ROAD SURFACE GENERATING SPARKS WHICH COULD IGNITE FLAMMABLE MATERIAL.

Remedy: OWNER NOTIFICATION IS BEING CONDUCTED BY NEWAY ANCHORLOK. DEALERS WILL INSPECT AND REPLACE ALL SUSPENSION SUSPENSION BEAMS WITH SUSPENSION BEAMS CONTAINING APPROPRIATE SHAFTS.

Reported: 1996-12-12 (December 12, 1996) · Model years: 1997

THESE VEHICLES ARE EQUIPPED WITH A DETROIT DIESEL OPTIMIZED IDLE SYSTEM. IF THE IGNITION IS TURNED ON AND THE FUSE FOR THE ELECTRONIC CONTROL MODULE (ECM) POWER FEED LINE IS REMOVED OR BURNED OUT, UNINTENTIONAL CRANKING OF THE ENGINE WILL OCCUR..

Consequence: IF UNINTENTIONAL CRANKING OF THE ENGINE OCCURS, THE SAFETY FEATURES DESIGNED TO PREVENT INJURY TO PERSONS WORKING IN THE VICINITY OF THE ENGINE WILL OCCUR AND ALSO VEHICLE MOVEMENT MAY OCCUR INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DETROIT DIESEL DISTRIBUTORS WILL REWIRE THE VEHICLES USING A REVISED ECM WHICH WILL ELIMINATE UNINTENTIONAL CRANKING.

Reported: 1996-11-22 (November 22, 1996) · Model years: 1997

THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED. THE LENGTH OF THE KEYWAY SLOT MAY NOT BE LONG ENOUGH TO ACCOMMODATE THE TAB CAUSING THE TAB TO BE DEFORMED OR DAMAGED DURING INSTALLATION.

Consequence: THIS LOCKING TAB PREVENTS THE WHEEL BEARING NUT FROM LOOSENING DURING VEHICLE OPERATION. IF THIS TAB IS DEFORMED, THE NUT CAN LOOSEN ALLOWING THE WHEEL TO SEPARATE FROM THE AXLE INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE DRIVE AXLE HOUSING NUTS WITH A CONVENTIONAL WHEEL NUT HARDWARE SYSTEM.

Reported: 1996-11-27 (November 27, 1996) · Model years: 1997

VEHICLE DESCRIPTION: SCHOOL BUSES AND HEAVY DUTY TRUCKS EQUIPPED WITH REAR AXLE ASSEMBLIES PRODUCED BY DANA SPICER. CERTAIN REAR AXLE ASSEMBLIES WERE IMPROPERLY HEAT TREATED WHICH COULD ALLOW PINION BREAKAGE AT THE PINION THREADS.

Consequence: CRACKS CAN INITIATE AND RESULT IN SEPARATION OF THE THREADED END OF THE PINION RESULTING IN SEPARATION OF THE YOKE AND DRIVE LINE FROM THE REAR AXLE INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE REAR AXLE CARRIER/PINION ASSEMBLY.

Reported: 2000-05-23 (May 23, 2000) · Model years: 1998, 1999, 2000

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL CODE 16SCH (LOWER BUNK WEBBING RESTRAINT). INCORRECT BOLTS WERE USED TO HOLD THE BUNK WEBBING RESTRAINT LATCH BRACKETS TO THE BUNK BASE.

Consequence: IN THE EVENT OF A CRASH, THE RESTRAINT MAY NOT CONTAIN THE OCCUPANT AND MAY RESULT IN PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH.

Remedy: DEALERS WILL INSPECT AND REPLACE ALL GRADE 5 BOLTS WITH GRADE 8 BOLTS AS REQUIRED.