Mack F recalls by model year

Reported: 1974-08-05 (August 5, 1974) · Model years: 1965, 1966, 1967

Reported: 1975-06-23 (June 23, 1975) · Model years: 1967, 1968, 1969, 1970, 1971, 1972, 1973

Reported: 1969-08-13 (August 13, 1969) · Model years: 1969

Reported: 1972-05-22 (May 22, 1972) · Model years: 1970, 1971

Reported: 1971-11-29 (November 29, 1971) · Model years: 1971

Reported: 1972-02-14 (February 14, 1972) · Model years: 1971

Reported: 1974-02-25 (February 25, 1974) · Model years: 1971, 1972

Reported: 1978-08-08 (August 8, 1978) · Model years: 1971, 1972, 1973, 1974

DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE LEFT STEERING KNUCKLE WITH AN IMPROVED TYPE OF KNUCKLE.

Reported: 1977-10-12 (October 12, 1977) · Model years: 1972, 1973, 1974, 1975, 1976, 1977

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.

Remedy: DEALER WILL REPLACE THE ORIGINAL FAN WITH A STEEL FIXED BLADE FAN, FREE OF CHARGE.

Reported: 1974-12-02 (December 2, 1974) · Model years: 1973

Reported: 1976-04-15 (April 15, 1976) · Model years: 1973

Reported: 1975-10-31 (October 31, 1975) · Model years: 1974, 1975

Reported: 1975-10-31 (October 31, 1975) · Model years: 1974, 1975

Reported: 1978-04-04 (April 4, 1978) · Model years: 1974, 1975, 1976

AN AXLE "NO BRAKE" CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.

Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE ANTI-WHEEL LOCK CONTROLLER WITHOUT CHARGE TO OWNER.

Reported: 1976-01-13 (January 13, 1976) · Model years: 1975

Reported: 1978-02-09 (February 9, 1978) · Model years: 1975, 1976, 1977, 1978

THE TEE BRACKET, WHICH IS MOUNTED ON THE FRONT AXLE OF THE BOGIE, MAY FAIL DUE TO VIBRATION BROUGHT ON BY ROAD SURFACE IRREGULARITIES. BRACKET FAILURE WOULD LEAVE THE TEE BRACKET UNSUPPORTED AND CAUSE BROKEN HOSE CONNECTOR FITTINGS. THIS WOULD RESULT IN AUTOMATIC APPLICATION OF THE SPRING EMERGENCY BRAKES.

Remedy: THE DEALER WILL REPLACE THE DEFECTIVE BRACKET WITH A REDESIGNED VERSION.

Reported: 1977-06-17 (June 17, 1977) · Model years: 1977

THE FRONT WHEEL RIM CLAMP STUDS, INSTALLED ON THE INVOLVED VEHICLES, MAY NOT HAVE BEEN MANUFACTURED CORRECTLY, CAUSING A BRITTLE CONDITION IN THE THREAD ROOT AREA. THE STUDS COULD EVENTUALLY CRACK AND BREAK WHEN WHEEL NUTS ARE TIGHTENED TO SPECIFICATIONS.

Remedy: THE DEALER WILL REPLACE ALL SUSPECT FRONT WHEEL STUDS, WITHOUT CHARGE TO OWNER.

Reported: 1977-10-12 (October 12, 1977) · Model years: 1977

THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEATBELT ASSEMBLIES". ALTHOUGH THE SEATBELTS IN QUESTION PERFORMED MARGINALLY WITH RESPECT TO THE 5000 LB. LOAD REQUIREMENT, ADDITIONAL TESTING CONFIRMED THAT THE ANCHOR COULD FAIL, ALLOWING EITHER THE ANCHOR TO SLIP OVER THE HOLD-DOWN NUT OR THE ANCHOR TO SEPARATE INTO TWO PIECES.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE SEAT BELT ASSEMBLIES WITHOUT CHARGE TO OWNER.

Reported: 1977-11-21 (November 21, 1977) · Model years: 1977

A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.

Remedy: DEALER WILL REWELD THE INSULATOR SPRING BRACKET AT NO COST TO OWNER.

Reported: 1978-10-03 (October 3, 1978) · Model years: 1977, 1978

DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, "AIR BRAKE SYSTEMS".

Remedy: DEALER WILL INSTALL NEW WHEEL SPEED SENSORS THAT INCORPORATE IMPROVED WIRING AND THE PRESENT BOGIE ANTI-WHEEL LOCK SYSTEM WILL BE CHANGED TO AN AXLE-TO-AXLE SYSTEM FOR IMPROVED RELIABILITY.

Reported: 1979-05-31 (May 31, 1979) · Model years: 1977, 1978, 1979

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.

Remedy: DEALER WILL INSTALL A SHIELD FOR THE HEADS OF THE FOUR CAPSCREWS, ALONG WITH STRONGER SAE 8 GRADE 8 CAPSCREWS, IF NECESSARY, AT NO COST TO OWNER.

Reported: 1979-01-12 (January 12, 1979) · Model years: 1978

THE STEEL BRACKETS ON THE SUSPENSION BEAM WERE FOUND TO BE DEFICIENT DUE TO EXCESSIVE SHRINKAGE AND LOW MECHANICAL PROPERTIES. FAILURE OF ONE OR BOTH OF THESE BRACKETS COULD CAUSE A SEPARATION OF THE AXLE HOUSING FROM THE SUSPENSION.

Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, REPLACE ANY SUSPECT BOGIE SPRING INSULATOR CAPS WITH NEW CAPS MEETING THE PROPER SPECIFICATIONS AT NO COST TO OWNER.

Reported: 1979-07-12 (July 12, 1979) · Model years: 1979

THE SPRING SEAT PLATE, LOCATED BETWEEN THE AXLE HOUSING AND THE SUSPENSION SPRINGS, MAY DEFORM DUE TO SPRING BENDING. AS A RESULT, THE CLAMPING FORCE IN THE ASSEMBLY MAY BE REDUCED. LOSS OF CLAMPING FORCE COULD CAUSE SPRING FAILURE AND THE AXLE WILL DISLOCATE. ALSO, THE TIRE COULD COME INTO CONTACT WITH THE SPRING.

Remedy: THE DEALER WILL REPLACE THE EXISTING SPRING SEAT WITH A NEWLY FABRICATED SEAT WHICH IS WELDED TO THE HOUSING. AN IMPROVED SPRING CLAMPING PLATE AND NEW SPRINGS WILL ALSO BE INSTALLED WITHOUT CHARGE.