Bmw 325 recalls by model year

Reported: 1993-02-01 (February 1, 1993) · Model years: 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993

THE MALFUNCTION OR FAILURE OF A COOLANT SYSTEM COMPONENT RESULTS IN SIGNIFICANTLY INCREASED COOLANT TEMPERATURE AND A RESULTING INCREASE IN SYSTEM PRESSURE.

Consequence: VEHICLES OPERATED UNDER THIS INCREASED COOLING SYSTEMPRESSURE CONDITION CAN SUFFER DAMAGE OR FAILURE OF PARTS OF THE COOLING SYSTEMSUCH AS (1) LEAKAGE FROM A COOLANT HOSE, (2) LEAKAGE OF THE RADIATOR OREXPANSION TANK, (3) DISCONNECTION OF A HOSE FROM A PIPE OR A FITTING, AND (4)CRACKS IN THE HEATER CORE END PIECE RESULTING IN COOLANT LEAKAGE. IN SOME CASES,BOILING COOLANT CAN CONTACT THE LOWER RIGHT LEG OF THE DRIVER RESULTING INBURNS. ALSO, ESCAPING COOLANT IN THE PASSENGER COMPARTMENT CAN CAUSE VAPORFOGGING OF THE INTERIOR SURFACE OF THE WINDOWS, REDUCING DRIVER VISIBILITY.

Remedy: DEALERS WILL INSTALL A THERMOSTATIC BYPASS VALVE IN THE ENGINE COMPARTMENT TO CONTROL COOLANT TEMPERATURE IN THE HEATER CORE. ALSO, A NEW DESIGN RADIATOR CAP WILL BE INSTALLED, TO CONTROL PRESSURE AND PROVIDE GREATER COOLANT OVERFLOW IN THE EVENT OF OVERHEATING.

Reported: 1986-10-20 (October 20, 1986) · Model years: 1985, 1986

THE TWO PARTS OF THE STEERING COLUMN DISENGAGEMENT ELEMENT COULD COMPLETELY DISCONNECT IF THE CAR CONTACTS AN OBJECT IN THE ROADWAY OR ELSEWHERE OF SUFFICIENT MASS TO APPLY A SIGNIFICANT FORCE DIRECTLY TO THE STEERING GEARBOX. CONSEQUENCE OF DEFECT: STEERING CONTROL WOULD BE LOST.

Remedy: BOLT TWO SPECIALLY FORMED PLATES TO THE DISENGAGEMENT ELEMENT SO THAT STEERING CAPABILITY WILL BE RETAINED.

Reported: 1986-11-10 (November 10, 1986) · Model years: 1986, 1987

BRAKE LIGHT SWITCH COULD OVERHEAT, EVENTUALLY LEADING TO MELTING OF PLASTIC INTERNAL PARTS IN AREA OF ELECTRICAL CONTACTS.

Consequence: CONSEQUENCE OF DEFECT: SWITCH PLUNGER COULD JAM, RENDERING BRAKE LIGHTS EITHER INOPERATIVE OR CONTINUOUSLY ILLIMINATED, REGARDLESS OF BRAKE PEDAL OPERATION.

Remedy: REPLACE BRAKE LIGHT SWITCH WITH REVISED SWITCH WITH INCREASED ELECTRICAL LOAD CAPACITY.

Reported: 1988-03-15 (March 15, 1988) · Model years: 1988

THE OIL DIPSTICK TUBE ATTACHING BRACKET MAY HAVE BEEN BENT DURING PRODUCTION OR SCHEDULED MAINTENANCE, REDUCING THE CLEARANCE BETWEEN THE DIPSTICK RING AND THE THROTTLE BELLCRANK LEVER.

Consequence: THIS REDUCED CLEARANCE MAY INHIBIT THE RETURN OF THETHROTTLE TO A FULLY CLOSED IDLE POSITION, WHEN THE ACCELERATOR PEDAL ISRELEASED.

Remedy: REQUIRES THE CUTTING OFF THE OUTBOARD END OF THE THROTTLE BELLCRANK LEVER TO PROVIDE NECESSARY CLEARANCE.

Reported: 1994-04-11 (April 11, 1994) · Model years: 1989, 1990, 1991, 1992, 1993

FEED FUEL HOSES CAN HARDEN AND "SET" OVER TIME, ALLOWING A SEEPAGE OF FUEL AT THE CONNECTION BETWEEN THE HOSE AND THE ENGINE FITTING. THE CLAMP USED TO HOLD THE HOSE TO THE FITTING IS UNABLE TO COMPENSATE FOR THE HARDENING OF THE FEED FUEL HOSE.

Consequence: FUEL SEEPAGE BETWEEN THE FEED FUEL HOSE AND THE ENGINE FITTING CAN RESULT IN FREE FUEL IN THE ENGINE COMPARTMENT, WHICH COULD RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.

Remedy: A REDESIGNED FEED FUEL HOSE AND HOSE CLAMP WILL BE INSTALLED TO ALLEVIATE THE FUEL SEEPAGE.

Reported: 1992-09-29 (September 29, 1992) · Model years: 1991

THE SCREW THAT SECURES THE WIPER SWITCH AT ONE LOCATION AND WHICH ALSO PROVIDES A GROUND FOR THE WIPER CIRCUIT, LOOSENS AS THE SWITCH IS OPERATED OVER A LONG PERIOD OF TIME. AS THE SCREW CONTINUES TO LOOSEN THE GROUND FOR THE WIPER CIRCUIT IS INTERMITTENTLY OR COMPLETELY LOST.

Consequence: THE INTERMITTENT OR COMPLETE LOSS OF THE WIPER CIRCUITGROUND CAUSES THE WIPERS TO OPERATE ERRATICALLY OR NOT AT ALL, RESULTING INREDUCED VISIBILITY FOR THE DRIVER IN INCLEMENT WEATHER CONDITIONS.

Remedy: RELOCATE THE WIPER SWITCH GROUND WIRE ATTACHMENT ON THE STEERING COLUMN.

Reported: 1992-04-14 (April 14, 1992) · Model years: 1992

THE VEHICLE FAILED TO COMPLY WITH FMVSS 208. THE DRIVER'S CHEST RESULTANT ACCELERATION EXCEEDED THE ALLOWABLE 60 G'S IN A CRASH TEST WHEN THE SEAT HEIGHT CHANGES ADJUSTMENT UNDER SEVERE FRONTAL IMPACT.

Consequence: THE DRIVER OF A VEHICLE FACES INCREASED RISK OF INJURYIN THE EVENT OF A SUDDEN STOP OR ACCIDENT.

Remedy: INSTALL A DAMPER ON THE UNDERSIDE OF THE DRIVER'S SEAT CUSHION, BETWEEN THE CUSHION FRAME AND THE SEAT TRACK. IN A SEVERE FRONTAL IMPACT THE DAMPER WILL HYDRAULICALLY LOCK, PREVENTING A CHANGE IN SEAT HEIGHT.

Reported: 1994-08-10 (August 10, 1994) · Model years: 1993, 1994

IN A FMVSS NO. 208 30 MILES-PER-HOUR COMPLIANCE TEST, AN UNBELTED TEST DRIVER DUMMY'S CHEST MAXIMUM RESULTANT ACCELERATION WAS 70.8 G'S, WHICH EXCEEDS THE MAXIMUM ALLOWABLE VALUE OF 60 G'S. ALSO, THE UNBELTED PASSENGER DUMMY'S LEFT FEMUR MAXIMUM LOAD WAS 2361 LBS, WHICH EXCEEDS MAXIMUM ALLOWABLE VALUE OF 2250 LBS. THE VEHICLES DO NOT COMPLY WITH FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: IN THE EVENT OF AN ACCIDENT, THE OCCUPANT WILL BE SUBJECTED TO AN INCREASED RISK OF INJURY.

Remedy: ON AUTOMATIC TRANSMISSION MODELS ONLY, THE DEALER WILL REPLACE THE TRANSMISSION SUPPORT CROSSMEMBER WITH A CROSSMEMBER USED ON THE MANUAL TRANSMISSION MODEL. ALSO, THE TRANSMISSION REAR BUSHING SUPPORTS WILL BE REPLACED WITH BUSHING HAVING DIFFERENT PERFORMANCE CHARACTERISTICS. THE STEERING COLUMN FRONT SUPPORT BEARING AT THE FIREWALL WILL BE REPLACED WITH A MODIFIED PART USING A TEFLON INNER SURFACE AND TEFLON SPRAY WILL BE APPLIED TO THE COLUMN HOUSING IN THE AREA OF THE BEARING. A BRACE WILL BE ADDED BETWEEN THE KNEE BOLSTER SUPPORT AND THE STEERING COLUMN.

Reported: 2017-01-20 (January 20, 2017) · Model years: 2000, 2001, 2002

BMW of North America, LLC (BMW) is recalling certain 2000-2002 BMW 320i, 323i, 325i, 325xi, 330i, 330xi, 323Ci, 325Ci, 330Ci, M3, 323iT, 325iT and 325xiT vehicles, 2001-2002 525i, 530i, 540i, M5, 525iT and 540iT vehicles, and 2001-2003 X5 3.0i, X5 4.4i, and X5 4.6is vehicles. These vehicles may have had a driver-side air bag module installed as replacement equipment such as after a vehicle crash necessitating replacement of the original air bag, or as a remedy part for a prior recall. These replacement modules contain an air bag inflator that may rupture due to propellant degradation occurring after long-term exposure to lower absolute humidity, temperature and temperature cycling.

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the vehicle has been remedied. BMW will notify owners, and dealers will inspect the driver side air bag module, replacing it as necessary, free of charge. The recall began March 15, 2017. Owners may contact BMW customer service at 1-800-525-7417.

Reported: 2019-10-02 (October 2, 2019) · Model years: 2000, 2001, 2002

BMW of North America, LLC (BMW) is recalling certain 2000-2002 325i and 325xi Sedan, and 323Ci, 325Ci, and 330Ci Convertible vehicles. This recall affects certain vehicles that may have had a driver-side air bag module installed as replacement equipment such as after a vehicle crash necessitating replacement of the original air bag, or as a remedy part for a prior recall. The frontal air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the vehicle has been remedied. BMW will notify owners, and dealers will inspect and, as necessary, replace the driver's air bag module, free of charge. The recall began November 7, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of previous recalls, numbers 17V-047 and 19V-015.

Reported: 2016-02-05 (February 5, 2016) · Model years: 2006, 2007, 2008, 2009, 2010, 2011, 2012

BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.