Buick REGAL recalls by model year

Reported: 1974-02-15 (February 15, 1974) · Model years: 1973

Reported: 1973-12-27 (December 27, 1973) · Model years: 1974

Reported: 1974-01-25 (January 25, 1974) · Model years: 1974

Reported: 1974-09-04 (September 4, 1974) · Model years: 1975

Reported: 1975-02-19 (February 19, 1975) · Model years: 1975

Reported: 1975-12-19 (December 19, 1975) · Model years: 1976

Reported: 1976-02-10 (February 10, 1976) · Model years: 1976

Reported: 1976-09-07 (September 7, 1976) · Model years: 1977

Reported: 1976-09-21 (September 21, 1976) · Model years: 1977

Reported: 1978-06-13 (June 13, 1978) · Model years: 1977

THE REAR AXLE SHAFTS MAY CONTAIN A FLAW IN THE METAL. THIS FLAW COULD ALLOW THE SHAFT TO BREAK AND THE TIRE AND WHEEL ASSEMBLY TO SEPARATE.

Remedy: THE DEALER WILL REPLACE ONE OR BOTH REAR AXLE SHAFTS, IF NECESSARY, FREE OF CHARGE.

Reported: 1978-01-24 (January 24, 1978) · Model years: 1978

THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS", IN THAT THE TIRE PLACARD DOES NOT CONTAIN LEGIBLE TIRE SIZE INFORMATION.

Remedy: DEALER WILL PROVIDE PROPER LABELS FOR THE OWNER TO INSTALL, OR FOR DEALER INSTALLATION, IF PREFERRED.

Reported: 1978-06-13 (June 13, 1978) · Model years: 1978

THE HUB PORTION OF THE FAN BLADE ASSEMBLY COULD CRACK DUE TO HIGH STRESS LEVELS GENERATED DURING ENGINE OPERATING CONDITIONS. EVENTUALLY, THE BLADE COULD BREAK APART AT THE HUB AND BLADE PIECES COULD BE PROPELLED INTO THE ENGINE. IF THE HOOD IS OPEN WHILE THE ENGINE IS RUNNING, THE FRAGMENTS WOULD BE FREE TO FLY FROM THE VEHICLE.

Remedy: DEALER WILL REPLACE THE FAN BLADE ASSEMBLY WITHOUT CHARGE TO OWNER.

Reported: 1979-07-23 (July 23, 1979) · Model years: 1978

UNDER CERTAIN DRIVING CONDITIONS, THESE VEHICLES CAN EXPERIENCE TEMPERATURES IN THE FRONT WHEEL OUTER BEARING AREA WHICH CAN AFFECT THE WHEEL BEARING GREASE. THIS CAN RESULT IN INADEQUATE LUBRICATION OF THE BEARING. THIS CONDITION MAY BE FURTHER AGGRAVATED BY IMPROPER ADJUSTMENT OF THE FRONT WHEEL SPINDLE NUT.

Remedy: THE DEALER WILL INSTALL NEW FRONT WHEEL OUTER BEARINGS PACKED WITH GREASE AND THE SPINDLE WILL BE COATED WITH LUBRICANT. NEW GREASE RETAINER CAPS WILL ALSO BE INSTALLED TO MAINTAIN GREASE IN OUTER BEARING. THIS WILL BE DONE FREE OF CHARGE.

Reported: 1981-02-25 (February 25, 1981) · Model years: 1978, 1979, 1980, 1981

THE BOLTS THAT ATTACH THE LOWER REAR CONTROL ARM TO THE FRAME MAY FRACTURE. THE REAR CONTROL ARM SUPPORTS AND POSITIONS THE REAR AXLE. FRACTURE OF THE BOLTS WOULD ALLOW THE CONTROL ARM TO DROP FREE.

Remedy: BOTH REAR CONTROL ARM ATTACHMENT BOLTS WILL BE REPLACED WITHOUT CHARGE.

Reported: 1984-11-24 (November 24, 1984) · Model years: 1978, 1979, 1980

REAR AXLE ASSEMBLY MAY HAVE AXLES THAT WERE IMPROPERLY MANUFACTURED. THIS CONDITION MAY RESULT IN SEPARATION OF THE AXLE SHAFT AND WHEEL ASSEMBLY FROM THE VEHICLE.

Remedy: THE DEALER WILL INSPECT THE REAR AXLE TO DETERMINE WHETHER IT WAS MANUFACTURED AT THE BUFFALO PLANT. IF SO, THEY WILL MAKE AXLE MEASUREMENTS AND IF NECESSARY REPLACE OR MODIFY AFFECTED AXLE COMPONENTS WITHOUT CHARGE.

Reported: 1985-04-29 (April 29, 1985) · Model years: 1978, 1980

EXCESSIVE ENLARGEMENT OF THE WHEEL CYLINDER PILOT HOLE IN THE REAR BRAKE BACKING PLATE COULD ALLOW THE WHEEL CYLINDER TO ROTATE AND CAUSE LOSS OF BRAKE FLUID. CONSEQUENCE OF DEFECT: A LOSS OF BRAKE FLUID LEADS TO LOSS OF REAR BRAKE ACTION, CREATING THE POTENTIAL FOR AN ACCIDENT. FRONT BRAKES WOULD REMAIN OPERATIONAL.

Remedy: ADD A PART TO PREVENT WHEEL CYLINDER FROM ROTATING.

Reported: 1979-06-06 (June 6, 1979) · Model years: 1979

ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH AT NO COST TO OWNER.

Reported: 1979-09-18 (September 18, 1979) · Model years: 1979

THE SHIFT CABLE RETAINING CLIP MAY HAVE BEEN INSTALLED BACKWARDS OR NOT AT ALL. THE PURPOSE OF THIS SPRING CLIP IS TO SECURE THE LOWER END OF THE SHIFT CABLE HOUSING TO THE TRANSMISSION. IF THE CLIP IS BACKWARD OR MISSING, THE CONSOLE SHIFT LEVER MAY NOT SHIFT THE TRANSMISSION AND/OR THE TRANSMISSION RANGE INDICATOR MAY INDICATE THAT THE TRANSMISSION IS IN THE "PARK" OR "P" POSITION WHEN IT IS NOT.

Remedy: THE DEALER WILL INSPECT AND IF NECESSARY CORRECT THE SHIFT CABLE RETAINING CLIP INSTALLATION AT NO CHARGE.

Reported: 1979-09-12 (September 12, 1979) · Model years: 1980

THE BOLTS THAT ATTACHED THE REAR SUSPENSION CONTROL ARMS TO THE FRAME AND AXLE MAY BE DEFECTIVE AND THE BOLT HEAD MAY SEPARATE FROM THE BOLT SHANK. THIS COULD ALLOW THE CONTROL ARM TO COME LOOSE.

Remedy: THE DEALER WILL REPLACE ALL SUSPECT REAR SUSPENSION CONTROL ARM BOLTS PRIOR TO DELIVERY. THIS WILL BE DONE FREE OF CHARGE.

Reported: 1979-10-23 (October 23, 1979) · Model years: 1980

THE INVOLVED VEHICLES MAY HAVE BEEN ASSEMBLED WITH CLEAR LAMP BULBS INSTEAD OF THE CORRECT AMBER BULBS IN FRONT PARK AND TURN SIGNAL LOCATIONS. AS A RESULT, THESE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT".

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE CLEAR PARK AND TURN SIGNAL LAMP BULBS WITH AMBER BULBS AT NO COST TO OWNER.

Reported: 1981-01-13 (January 13, 1981) · Model years: 1981

THE STEEL USED IN SOME COMPACT SPARE WHEELS IS TOO THIN. WHILE IN SERVICE THE WHEEL MAY FRACTURE, RESULTING IN A PARTIAL OR COMPLETE SEPARATION OF THE WHEEL AND TIRE FROM THE VEHICLE.

Remedy: SPARE WHEELS WILL BE REPLACED WITHOUT CHARGE TO OWNERS WITHIN 60 DAYS OF RECALL NOTIFICATION.

Reported: 1981-03-23 (March 23, 1981) · Model years: 1981

"TX" HEAVY DUTY WHEELS MAY HAVE BEEN MANUFACTURED WITH LAMINATED STEEL. THE WHEEL DISC MAY FRACTURE AND THE WHEEL AND TIRE COULD PARTIALLY OR COMPLETELY SEPARATE FROM THE VEHICLE.

Remedy: THE DEFECTIVE WHEELS WILL BE REPLACED WITHOUT CHARGE.

Reported: 1982-01-03 (January 3, 1982) · Model years: 1982

UNDER CERTAIN VEHICLE OPERATING CONDITIONS, THE GOVERNOR WEIGHT RETAINER IN THE INJECTION PUMP MAY FAIL. THE THROTTLE VALVE COULD STICK, PREVENTING RETURN TO IDLE AND SHUT DOWN OF THE ENGINE BY THE DRIVER.

Remedy: DEALER WILL REPLACE THE GOVERNOR WEIGHT ASSEMBLY IN THE INJECTION PUMP AT NO COST TO OWNER.

Reported: 1982-08-24 (August 24, 1982) · Model years: 1982

THE FUEL INLET PIPE MAY DEVELOP CRACKS AT THE FLARED END LEADING INTO THE CARBURETOR DUE TO VIBRATIONS IN OPERATION. THESE CRACKS COULD RESULT IN FUEL LEAKAGE.

Remedy: DEALER WILL INSTALL A NEW FUEL INLET PIPE ON THE INVOLVED VEHICLES, FREE OF CHARGE.

Reported: 1983-10-13 (October 13, 1983) · Model years: 1983

THE MASTER CYLINDER REAR BRAKE PIPE, WHICH CARRIES BRAKE FLUID TO THE REAR BRAKES, MAY DEVELOP A LEAK DUE TO EXTENDED CHAFING ON THE AIR CLEANER RESONATOR BRACKET.

Remedy: IF UPON INSPECTION THE DEALER FINDS THAT THERE IS INADEQUATE CLEARANCE, THE PIPE WILL BE REFORMED TO OBTAIN THE NECESSARY THREE QUARTER INCH SPACE. ONLY THOSE PIPES SHOWING SIGNS OF WEAR WILL BE REPLACED.

Reported: 1984-02-06 (February 6, 1984) · Model years: 1984

SOME VEHICLES HAVE BUCKET SEAT BACK LOCKS THAT DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD 207, ANCHORAGE OF SEATS. IN EVENT OF A CRASH, THE SEAT BACK LOCK MAY NOT FUNCTION.

Remedy: INSPECTION OF SEAT BACK LOCKS WILL BE PERFORMED. LOCKS THAT HAVE BENT, BROKEN OR MISSING HOOKS WILL BE REPLACED.

Reported: 1985-03-05 (March 5, 1985) · Model years: 1984

ONE OF THE THREE STEERING GEAR TO FRAME BOLTS MAY NOT HAVE BEEN TIGHTENED TO THE REQUIRED SPECIFICATION. CONSEQUENCE OF DEFECT: THE STEERING GEAR COULD COME LOOSE FROM THE FRAME CAUSING A LOSS OF STEERING CONTROL AND A POSSIBLE VEHICLE CRASH WITHOUT WARNING.

Remedy: TIGHTEN THE STEERING GEAR TO FRAME BOLTS.

Reported: 1985-04-29 (April 29, 1985) · Model years: 1984, 1985

THE REAR BUMPER MAY FRACTURE DURING A REAR END COLLISION, PUNCTURE THE FUEL TANK, AND CAUSE A FUEL LEAK. CONSEQUENCE OF DEFECT: A FUEL LEAK CREATES THE POTENTIAL FOR A FIRE WHICH COULD RESULT IN BURN INJURIES TO PERSONS IN OR NEAR THE CAR.

Remedy: REPLACE THE REAR BUMPER BRACKETS AND THE "L" SHAPED REINFORCEMENT WITH A "U" SHAPED FULL REINFORCEMENT.

Reported: 1989-06-16 (June 16, 1989) · Model years: 1984, 1986, 1987

A SMALL NYLON BUSHING IN THE CRUISE CONTROL SERVO BAIL MAY SLIP OUT OF PLACE, CAUSING INTERMITTENT AND UNEXPECTED INCREASES IN ENGINE SPEED OR DIESELING (ENGINE RUN ON WITH IGNITION OFF).

Consequence: SERVO ROD ASSEMBLY COULD CATCH ON ENGINE COMPONENTS ANDRESULT IN A STUCK THROTTLE WITH POTENTIAL FOR A VEHICLE CRASH.

Remedy: INSTALL A NEW BUSHING IN CRUISE CONTROL SERVO BAIL.

Reported: 1984-10-10 (October 10, 1984) · Model years: 1985

THE TIE RODS ARE PART OF THE STEERING LINKAGE AND TRANSMIT TURNING MOVEMENTS TO THE WHEELS. THE BOLTS THAT FASTEN THE TIE RODS TO THEIR ADJUSTERS MAY NOT BE TIGHT ENOUGH. THIS COULD ALLOW THE TIE ROD TO LOOSEN AND DETACH ITSELF FROM THE ADJUSTER.

Remedy: THE TIE ROD END BOLTS WILL BE TIGHTENED WITHOUT COST TO THE OWNER.

Reported: 1984-11-27 (November 27, 1984) · Model years: 1985

THE VEHICLES WERE ASSEMBLED WITH FRONT SEAT BELT RETRACTORS WHICH MAY NOT PERFORM ADEQUATELY DURING A COLLISION.

Remedy: THE DEALER WILL REPLACE THE LEFT AND RIGHT FRONT SEAT BELT RETRACTORS FREE OF CHARGE.

Reported: 1985-04-26 (April 26, 1985) · Model years: 1985

A LOSS OF BONDING ADHESION BETWEEN THE PAINT AND THE WINDSHIELD OPENING AREA COULD ALLOW THE WINDSHIELD TO SEPARATE DURING A 30 MILE PER HOUR FRONTAL BARRIER TEST REQUIRED BY FMVSS 212, WINDSHIELD RETENTION. CONSEQUENCE OF DEFECT: WINDSHIELD SEPARATION DURING AN ACCIDENT COULD RESULT IN AN UNBELTED OCCUPANT BEING EJECTED FROM THE CAR AND SEVERLY INJURED.

Remedy: REMOVE AND REINSTALL WINDSHIELD IF A LACK OF PAINT BONDING IS EVIDENT.

Reported: 1985-09-19 (September 19, 1985) · Model years: 1985

THE CERTIFICATION LABEL LOCATED ON THE LEFT FRONT DOOR DID NOT INCLUDE A REQUIRED FEDERAL CERTIFICATION STATEMENT. CONSEQUENCE OF DEFECT: VEHICLES DO NOT COMPLY WITH FEDERAL REGULATION 567.

Remedy: LABELS CONTAINING CORRECT INFORMATION ARE BEING MAILED AND SHOULD BE INSTALLED ON THE LEFT FRONT DOOR.

Reported: 1986-02-21 (February 21, 1986) · Model years: 1985

THE THROTTLE RETURN SPRING ASSEMBLY MAY FAIL PREVENTING THE THROTTLE FROM RETURNING TO THE CLOSED (IDLE) POSITION WHEN THE ACCELERATOR PEDAL IS RELEASED. CONSEQUENCE OF DEFECT: ENGINE SPEED MAY NOT DECREASE AND LOSS OF ACCELERATOR CONTROL COULD RESULT IN AN ACCIDENT WITHOUT PRIOR WARNING.

Remedy: REPLACE THROTTLE RETURN SPRING.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1985, 1986

SMALL CRACKS MAY DEVELOP IN THE BODY PILLAR AROUND THE DOOR STRIKER BOLT HOLE.

Consequence: CRACKS WOULD INCREASE LEADING TO DIFFICULTY IN CLOSINGTHE DOOR AND MIGHT ALLOW DOOR TO COME OPEN DURING A CRASH, INCREASINGLIKELIHOOD OF INJURY TO OCCUPANTS.

Remedy: INSTALL INNER AND OUTER REINFORCEMENT PLATE ON BOTH LEFT AND RIGHT BODY PILLARS.

Reported: 1988-01-08 (January 8, 1988) · Model years: 1985, 1986

UNDER EXTENDED HEADLAMP USAGE, CIRCUITRY IN THE HEADLAMP SWITCH PANEL MIGHT EXPERIENCE INCREASED RESISTANCE AND EXCESSIVE HEAT BUILDUP.

Consequence: HEADLIGHTS WOULD CYCLE ON AND OFF. SUDDEN LOSS OFHEADLIGHTS UNDER SEVERE WEATHER OR NIGHTIMER DRIVING CONDITIONS COULD RESULTIN A VEHICLE CRASH.

Remedy: REPLACE HEADLIGHT SWITCH WITH MODIFIED SWITCH.

Reported: 1986-07-14 (July 14, 1986) · Model years: 1986

LEFT HANDED DRIVER'S SIDE SHOULDER BELT ANCHOR PLATE MAY BE UPSIDE DOWN IN LOCK PILLAR SO THAT THE UNTHREADED SLOT OF THE PLATE ALIGNED WITH THE HOLE IN THE LOCK PILLAR. THIS RESULTED IN THE ANCHOR BOLT BEING DRIVEN INTO THE SLOT INSTEAD OF THE THREADED HOLE OF THE ANCHOR PLATE. CONSEQUENCE OF DEFECT: IN A VEHICLE CRASH, BELT ANCHOR BOLT MAY PULL LOOSE FROM ANCHOR PLATE, THUS FAILING TO COMPLY WITH FMVSS 210, SEAT BELT ASSEMBLY ANCHORAGES, AND INCREASES LIKELIHOOD OF INJURY TO OCCUPANT.

Remedy: INSTALL A BOLT ANCHOR PLATE REINFORCEMENT AND NEW BOLT, AS NECESSARY.

Reported: 1987-10-26 (October 26, 1987) · Model years: 1987

MANUAL VALVE LINK IN THE TRANSMISSION MAY HAVE BEEN IMPROPERLY FORMED.

Consequence: THE VALVE LINK COULD SEPARATE RESULTING IN A GEARSELECTION DIFFERENT FROM WHAT THE DRIVER SELECTS. ALSO, CAR COULD BE STARTEDWITH TRANSMISSION IN GEAR ALLOWING VEHICLE TO MOVE IN AN UNANTICIPATEDDIRECTION.

Remedy: REPLACE THE MANUAL VALVE DETENT LEVER LINK.

Reported: 2000-07-11 (July 11, 2000) · Model years: 1988, 1989, 1990, 1991

VEHICLE DESCRIPTION: PASSENGER VEHICLES ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE STATES OF CONNECTICUT, DELAWARE, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA, WISCONSIN, AND THE DISTRICT OF COLUMBIA, WHERE ROAD SALT USE IS HEAVY. A CONDITION WHERE ONE OR BOTH FRONT ENGINE CRADLE BOLTS CAN PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINERS.

Consequence: IF BOTH BOLTS PULL THROUGH, THE FRONT OF THE CRADLE WOULD NO LONGER BE SUPPORTED AT THE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT COULD SEPARATE FROM THE STEERING GEAR.

Remedy: DEALERS WILL REPLACE THE FRONT AND REAR FRAME/CRADLE BOLTS AND RETAINERS.

Reported: 1988-03-24 (March 24, 1988) · Model years: 1988

THE STOP LAMP SWITCH MAY HAVE A LOOSE ELECTRICAL CONTACT. THE LOOSE CONTACT CAN OVERHEAT AND MELT THE SURROUNDING PLASTIC CAUSING THE CONTACT TO STICK OPEN.

Consequence: AN OPEN CONTACT WOULD RENDER THE BRAKE LIGHTS INOPERATIVEWHEN THE BRAKE PEDAL IS DEPRESSED. ALSO, THE TRANSMISSION CLUTCH CONTROL ANDCRUISE CONTROL CONTACTS WOULD REMAIN CLOSED. THIS CONDITION WOULD RESULT INCRUISE RESUME UPON BRAKE PEDAL RELEASE IF THE CRUISE CONTROL IS IN THE ONPOSITION. EITHER AN UNEXPECTED CRUISE RESUME OR INOPERATIVE BRAKE LIGHTS COULDRESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.

Remedy: THE ROTARY SOPLAMP SWITCH WILL BE REPLACED ON ALL INVOLVED VEHICLES.

Reported: 1988-03-28 (March 28, 1988) · Model years: 1988

AN INTERFERENCE BETWEEN THE TRANSMISSION SHIFT CABLE AND THE BELLCRANK CLIP IN THE STEERING COLUMN CAN RESULT IN DISENGAGEMENT OF THE TRANSMISSION CABLE.

Consequence: THIS CONDITION COULD ALLOW THE TRANSMISSION TO BE IN AGEAR OTHER THAN THAT DISPLAYED BY THE SHIFT INDICATOR. THE VEHICLE COULD MOVEIN AN UNEXPECTED DIRECTION AND CAUSE A VEHICLE CRASH WITHOUT PRIOR WARNING.

Remedy: A NEWLY DESIGNED BELLCRANK CLIP WILL BE INSTALLED.

Reported: 1988-04-18 (April 18, 1988) · Model years: 1988

THE SECONDARY HOOD LATCH MAY NOT PROPERLY ENGAGE.

Consequence: IF PRIMARY LATCH DISENGAGES, HOOD COULD UNEXPECTEDLYOPEN. IF CAR WAS IN MOTION, HOOD COULD CONTACT THE WINDSHIELD, REDUCE THEDRIVERS FORWARD VISION AREA, AND COULD RESULT IN AN ACCIDENT.

Remedy: REPLACE SECONDARY LATCH WITH A NEW LATCH.

Reported: 1988-04-18 (April 18, 1988) · Model years: 1988

LOWER CONTROL ARM TO BALL JOINT ATTACHMENT CAN BECOME LOOSE. ALSO, CERTAIN CARS COULD HAVE TIE ROD BALL STUD NUTS THAT WERE NOT PROPERLY TORQUED AND COULD LOOSEN.

Consequence: CONTINUED OPERATION OF CAR WITH EITHER CONDITION COULDRESULT IN SEPARATION OF THAT JOINT AND POSSIBLE LOSS OF STEERING CONTROL AND ANACCIDENT.

Remedy: REPLACE BOTH LOWER CONTROL ARMS; ALSO, CHECK TIE ROD BALL STUD NUT TORQUE.

Reported: 1988-07-06 (July 6, 1988) · Model years: 1988

TWISTED COMPONENTS COULD ALLOW THE LEFT FRONT BRAKE HOSE TO CONTACT THE FENDER LINING/RAIL AREA; OVER TIME THE BRAKE HOSE COULD WEAR THROUGH.

Consequence: THIS COULD RESULT IN A LOSS OF BRAKE FLUID AND A PARTIALLOSS OF BRAKING CAPABILITY WHICH COULD RESULT IN AN ACCIDENT.

Remedy: INSPECT LEFT FRONT BRAKE HOSE FOR PROPER INSTALLATION AND REPLACE, AS NECESSARY.

Reported: 1990-03-14 (March 14, 1990) · Model years: 1988, 1989, 1990

FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT FASTENER MAY PULL THROUGH DOOR MOUNTED ANCHOR PLATE.

Consequence: SEAT BELT MAY NOT SUSTAIN LOADS REQUIRED BY FMVSS 210, AND IN A VEHICLE ACCIDENT, THE SEAT BELT MAY NOT PROPERLY RESTRAIN A PASSENGER, RESULTING IN INCREASED RISK OF GREATER INJURY TO AN OCCUPANT.

Remedy: REPLACE FRONT SHOULDER BELT GUIDE LOOP ATTACHMENT NUTS AND INSTALL NEW GUIDE COVER.

Reported: 1995-03-28 (March 28, 1995) · Model years: 1988, 1989, 1990

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

Consequence: IF WHEEL SEPARATION OCCURS WHILE THE VEHICLE IS IN MOTION, LOSS OF STEERING AND BRAKE CONTROL OF THE VEHICLE OCCURS, AND A VEHICLE CRASH COULD RESULT WITHOUT PRIOR WARNING.

Remedy: DEALERS WILL INSPECT THE MANUFACTURING CODES STAMPED ON EACH WHEEL OF THE VEHICLE AND IF A WHEEL FALLS WITHIN THE SPECIFIED DATE CODE RANGE, THE DEALER WILL REPLACE THAT WHEEL ASSEMBLY.

Reported: 1995-06-05 (June 5, 1995) · Model years: 1988, 1989, 1990

CRACKS DEVELOP IN THE WHEEL MOUNTING SURFACE. IF THESE CRACKS BECOME SEVERE ENOUGH, THE WHEEL WILL COMPLETELY SEPARATE FROM THE VEHICLE.

Consequence: IF WHEEL SEPARATION OCCURS WHILE THE VEHICLE IS IN MOTION, LOSS OF STEERING AND BRAKE CONTROL OF THE VEHICLE OCCURS, AND A VEHICLE CRASH COULD RESULT WITHOUT PRIOR WARNING.

Remedy: DEALERS WILL INSPECT THE MANUFACTURING DATE CODES STAMPED ON EACH WHEEL OF THE VEHICLE AND IF A WHEEL FALLS WITHIN THE SPECIFIED DATE CODE RANGE, THE DEALER WILL REPLACE THAT WHEEL ASSEMBLY.

Reported: 1997-04-08 (April 8, 1997) · Model years: 1988, 1989, 1990, 1991

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE RETAINERS DUE TO CORROSION OF THE RETAINER. IF BOTH BOLTS PULL THROUGH, THE REAR CRADLE WOULD NOT LONGER BE SUPPORTED AT THESE MOUNTING LOCATIONS AND THE STEERING INTERMEDIATE SHAFT CAN SEPARATE FROM THE STEERING GEAR.

Consequence: IF THIS WERE TO OCCUR WHILE THE VEHICLE WAS IN MOTION, A VEHICLE CRASH COULD RESULT.

Remedy: DEALERS WILL REPLACE THE REAR CRADLE BOLTS AND RETAINERS.

Reported: 1988-12-06 (December 6, 1988) · Model years: 1989

FUEL RETURN LINES COULD FRACTURE AND ALLOW FUEL TO LEAK IN THE AREA OF THE FUEL TANK.

Consequence: IN PRESENCE OF AN IGNITION SOURCE, THIS CONDITION COULDRESULT IN A FIRE.

Remedy: INSTALL NEW FUEL RETURN PIPE ASSEMBLY.

Reported: 1990-10-16 (October 16, 1990) · Model years: 1989, 1990

BRAKE STOPLAMPS MAY NOT ILLUMINATE OR, IN SOME CASES, STOPLAMPS WILL NOT STAY ILLUMINATED ALL THE TIME WHEN BRAKES ARE APPLIED DUE TO A FAULTY STOPLAMP SWITCH. ALSO IN VEHICLES EQUIPPED WITH CRUISE CONTROL, A FAULTY STOPLAMP SWITCH CAN RESULT IN RESUMPTION OF THE CRUISE CONTROL FUNCTION UPON RELEASE OF THE BRAKE PEDAL.

Consequence: A TRAILING VEHICLE MAY NOT RECOGNIZE A BRAKING ACTIONIN TIME TO RESPOND APPROPRIATELY. ALSO, CRUISE CONTROL WILL REENGAGE UPONRELEASE OF THE BRAKE PEDAL AND RESUME THE SET SPEED. IN EITHER CASE, IT COULDRESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL AN IMPROVED DESIGN STOPLAMP SWITCH.

Reported: 1990-06-06 (June 6, 1990) · Model years: 1990

OWNERS MANUALS DID NOT FULLY EXPLAIN HOW FRONT SHOULDER BELT COMFORT FEATURE WORKS.

Consequence: CARS WOULD NOT COMPLY WITH FMVSS 208, AND INCORRECT USE OF SAFETY RESTRAINTS COULD LEAD TO PERSONAL INJURY TO OCCUPANTS IF AN ACCIDENTSHOULD OCCUR.

Remedy: INSERT STICKER THAT PROVIDES MISSING INFORMATION IN OWNERS MANUALS.

Reported: 1991-10-02 (October 2, 1991) · Model years: 1990, 1991

FRONT SHOULDER SAFETY BELT WEBBING MAY SEPARATE AT FRONT BELT UPPER GUIDE LOOPS ON EITHER SIDE OF THE FRONT SEAT.

Consequence: WEBBING SEPARATION COULD OCCUR WITHOUT PRIOR WARNING ANDINCREASE THE RISK OF INJURY TO BELTED FRONT OUTBOARD OCCUPANTS IN A HIGH ENERGYCRASH.

Remedy: INSTALL A CONTROLLED ROTATION BRACKET ON DRIVER AND PASSENGER SIDE FRONT SEAT BELT GUIDE LOOPS.

Reported: 1992-01-10 (January 10, 1992) · Model years: 1991

THE FRONT DOOR SHOULDER BELT GUIDE LOOPS MAY BE CRACKED AND ARE NOT IN COMPLIANCE WITH FMVSS 208.

Consequence: THE SEAT OCCUPANT FACES INCREASED RISK OF INJURY IN THEEVENT OF A SUDDEN STOP OR ACCIDENT.

Remedy: INSTALL REINFORCING PLATES ON THE CRACKED SHOULDER BELT GUIDES.

Reported: 1993-09-03 (September 3, 1993) · Model years: 1991

THE FUEL FEED HOSE CAN PULL OUT OF THE CRIMPED COUPLING AT THE ENGINE END OF THE HOSE ASSEMBLY, CAUSING FUEL LEAKAGE.

Consequence: IF THE COUPLING WERE TO SEPARATE AND AN IGNITION SOURCEIS PRESENT, AN ENGINE COMPARTMENT FIRE COULD OCCUR.

Remedy: INSTALL A NEW FUEL FEED HOSE.

Reported: 1995-08-08 (August 8, 1995) · Model years: 1991, 1992, 1993, 1994, 1995

INCORRECT CLEAR FRONT SIDE MARKER BULBS WERE INSTALLED RATHER THAN AMBER BULBS. THIS DOES NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: DURING ILLUMINATION, THE BULBS WILL SHOW CLEAR RATHER THAN AMBER AND COULD MOMENTARILY CONFUSE OTHER DRIVERS.

Remedy: DEALERS WILL REPLACE THE CLEAR BULBS WITH THE CORRECT AMBER BULBS.

Reported: 1991-12-06 (December 6, 1991) · Model years: 1992

THE REVERSE SERVO APPLY PIN MAY BIND IN THE CASE WHICH COULD CAUSE REVERSE BAND DISTRESS (LOSS OR SLIPPING OF REVERSE), REVERSE BAND DRAG IN DRIVE RANGE (POOR PERFORMANCE -- POOR POWER), OR THE TRANSMISSION TO REMAIN IN REVERSE WHILE THE SHIFT INDICATOR SHOWS NEUTRAL GEAR POSITION.

Consequence: IF THE TRANSMISSION REMAINS IN REVERSE WHILE THE SHIFTINDICATOR SHOWS NEUTRAL, THE VEHICLE MAY UNEXPECTEDLY MOVE REARWARD AND RESULTIN A VEHICLE ACCIDENT.

Remedy: REPLACE THE TRANSAXLE WHERE REQUIRED.

Reported: 1993-03-09 (March 9, 1993) · Model years: 1993

THE DRIVER AND PASSENGER FRONT SEAT MANUAL RECLINING MECHANISMS DO NOT COMPLY WITH THE REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS." THE SEAT BACK MECHANISMS WILL NOT LATCH UNDER CERTAIN CONDITIONS.

Consequence: THE SEATS MAY RECLINE WITHOUT PRIOR WARNING, RESULTINGIN A HAZARD TO SEAT OCCUPANTS AND POSSIBLE LOSS OF VEHICLE CONTROL.

Remedy: REPLACE THE MANUAL SEAT RECLINER MECHANISM WITH A MECHANISM THAT COMPLIES WITH FMVSS 207.

Reported: 1995-03-22 (March 22, 1995) · Model years: 1994, 1995

THE REAR WHEEL BRAKE HOSE(S) CAN CONTACT THE REAR SUSPENSION COMPONENTS CAUSING THE BRAKE HOSE(S) TO WEAR THROUGH.

Consequence: THIS CONDITION CAN CAUSE LOSS OF BRAKE FLUID AND EVENTUAL LOSS OF THE VEHICLE BRAKING SYSTEM INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT FOR PROPER BRAKE HOSE POSITION AND REPLACE THOSE HOSES IN AN INCORRECT POSITION WITH NEW HOSES AND CORRECTLY ROUTED.

Reported: 1997-02-11 (February 11, 1997) · Model years: 1994, 1995

SOME OF THESE VEHICLES HAVE A STRAINED OR SEPARATED WASHER/WIPER SWITCH POWER FEED WIRE.

Consequence: THIS CAN CAUSE THE WINDSHIELD WASHER/WIPER TO WORK INTERMITTENTLY AND COULD ULTIMATELY RESULT IN INOPERATIVE WIPERS. IF THIS WERE TO OCCUR IN A SEVERE WEATHER SITUATION, DRIVER VISIBILITY COULD BE REDUCED, INCREASING THE RISK OF A VEHICLE CRASH.

Remedy: DEALERS WILL INSPECT AND REPLACE THE OLD DESIGNED WASHER/WIPER SWITCHES WITH A NEWLY DESIGNED SWITCH.

Reported: 2000-07-03 (July 3, 2000) · Model years: 1995

VEHICLE DESCRIPTION: PASSENGER VEHICLES. CORROSION OF THE AIR BAG INFLATOR'S INTERNAL WIRING, WHICH CAN OCCUR OVER TIME, COULD CAUSE THE INADVERTENT DEPLOYMENT OF THE DRIVER'S AIR BAG. THIS DEPLOYMENT COULD OCCUR DURING VEHICLE START-UP, WHILE THE VEHICLE IS PARKED OR IDLING, OR WHILE IN OPERATION.

Consequence: IF THE CONSUMER IS TOO CLOSE TO AN INFLATING AIR BAG, SERIOUS INJURIES COULD OCCUR.

Remedy: DEALERS WILL REPLACE THE INFLATORS ON THESE AIR BAGS.

Reported: 1994-11-21 (November 21, 1994) · Model years: 1995

THE VEHICLES WERE ASSEMBLED WITH AN INCORRECT FRONT PARK/TURN SIGNAL BULB WHICH DOES NOT HAVE SUFFICIENT CANDLE POWER. THIS DOES NOT COMPLY WITH FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: OPERATORS COULD FAIL TO NOTICE AND HEED THE WARNING LABELS. REDUCES CANDLE POWER ON THE PARK/TURN LIGHTS DECREASES THE LIKLIHOOD OF VEHICLE OPERATOR'S INTENT BEING SEEN BY OTHER MOTORISTS.

Remedy: DEALERS WILL REPLACE THE INCORRECT BULB WITH THE CORRECT BULB.

Reported: 1995-02-27 (February 27, 1995) · Model years: 1995

THE FOUR (4) STEERING COLUMN SUPPORT BRACKET ATTACHING BOLTS WERE UNDER TORQUED DURING ASSEMBLY.

Consequence: INADEQUATE TORQUE CAN CAUSE THESE BOLTS TO VIBRATE, LOOSEN, OR FALL OUT RESULTING IN LOSS OF STEERING CONTROL AND INCREASE THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL RETORQUE THE STEERING COLUMN SUPPORT BRACKET ATTACHING BOLTS TO THE CORRECT SPECIFICATIONS.

Reported: 1997-04-18 (April 18, 1997) · Model years: 1995

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE SEAT BELT SYSTEM CAN FRACTURE AND INJURY TO THE SEAT OCCUPANT CAN OCCUR.

Remedy: DEALERS WILL REPLACE THE CENTER REAR SEAT BELT SYSTEM.

Reported: 1998-12-01 (December 1, 1998) · Model years: 1995

THE CENTER REAR SEAT BELT ANCHOR PLATE EXHIBITS STRESS CRACKS.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE SEAT BELT SYSTEM CAN FRACTURE, INCREASING THE RISK OF INJURY TO THE SEAT OCCUPANT.

Remedy: DEALERS WILL REPLACE THE CENTER REAR SEAT BELT SYSTEM.

Reported: 2003-12-11 (December 11, 2003) · Model years: 1996, 1997, 1998

CERTAIN PASSENGER VEHICLES HAVE LOWER PINION BEARINGS IN THE POWER RACK AND PINION ASSEMBLY IN WHICH THE RETAINER TABS WERE NOT CRIMPED PROPERLY. THESE RETAINERS COULD FAIL AND PERMIT THE BALL BEARINGS TO ESCAPE.

Consequence: IF THIS OCCURS, THE PINION SHAFT CAN BE FORCED UPWARD DURING LEFT TURNS AND BACK DOWN AS THE STEERING WHEEL IS MOVED BACK AND TO THE RIGHT. IF THE PINION SHAFT MOVES FURTHER, THE DRIVER WILL NEED TO EXERT MORE EFFORT TO TURN THE STEERING WHEEL, SIMILAR TO A VEHICLE WITHOUT POWER ASSISTED STEERING. IF THE PINION SHAFT MOVES EVEN FURTHER, THE DRIVER WILL REQUIRE MUCH HIGHER EFFORT TO TURN LEFT AND MAY NOT BE ABLE TO TURN THE WHEEL AS MUCH AS INTENDED. WITH THE MAXIMUM PINION SHAFT MOVEMENT, WHICH REQUIRES INTERNAL GEAR COMPONENT DAMAGE, THE DRIVER CAN ENCOUNTER HIGH RESISTANCE TO TURNING LEFT, FOLLOWED BY UNINTENDED POWER ASSIST TO THE RIGHT. IN ANY OF THESE CONDITIONS, A CRASH COULD OCCUR.

Remedy: DEALERS WILL INSTALL A NEW LOWER PINION BEARING UNLESS INSPECT OF THE EXISTING BEARING INDICATES THAT REPLACEMENT OF THE GEAR ASSEMBLY IS NECESSARY. OWNER NOTIFICATION BEGAN ON FEBRUARY 5, 2004. OWNERS SHOULD CONTACT BUICK AT 1-866-608-8080; CHEVROLET AT 1-800-630-2438; OLDSMOBILE AT 1-800-630-6537; OR PONTIAC AT 1-800-620-7668.

Reported: 1996-04-19 (April 19, 1996) · Model years: 1996

THE LEFT FRONT BRAKE LINE CAN CONTACT THE TRANSAXLE MOUNTING BRACKET OR ATTACHMENT BOLT.

Consequence: THIS CONDITION CAN CAUSE THE BRAKE LINE TO WEAR THROUGH, RESULTING IN LOSS OF BRAKE FLUID AND EVENTUAL LOSS OF ONE-HALF OF THE VEHICLE'S BRAKE SYSTEM, INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT THE VEHICLE FOR PROPER BRAKE LINE CLEARANCE AND REPOSITION THOSE BRAKE LINES FOUND TO HAVE LESS THAN MINIMAL CLEARANCE. ADDITIONALLY, THOSE BRAKE LINES FOUND TO HAVE AN INDENTATION CAUSED BY THE CONTACT WILL BE REPLACED AND PROPERLY ROUTED.

Reported: 1996-07-01 (July 1, 1996) · Model years: 1996

A BACKFIRE DURING ENGINE STARTING CAN CAUSE BREAKAGE OF THE UPPER INTAKE MANIFOLD.

Consequence: THIS CONDITION CAN CAUSE A NO-START CONDITION AND POSSIBLY AN ENGINE COMPARTMENT FIRE.

Remedy: DEALERS WILL UPDATE THE POWERTRAIN CONTROL MODULE PROGRAMMING. UNTIL THE CAMPAIGN REPAIR IS MADE, THE VEHICLE HOOD SHOULD BE SHUT WHENEVER STARTING THE VEHICLE TO REDUCE THE CHANCE OF PERSONAL INJURY.

Reported: 2008-03-12 (March 12, 2008) · Model years: 1997, 1998, 1999, 2000, 2001, 2002, 2003

GM IS RECALLING 207,542 MY 1997-2003 BUICK REGAL AND PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L SUPERCHARGED V-6 ENGINE. THESE VEHICLES HAVE HIGHER FRONT ROCKER COVER GASKET TEMPERATURES, CREATING THE POTENTIAL FOR EARLIER DEGRADATION OF THE FRONT ROCKER COVER GASKET AND EVENTUAL OIL SEEPAGE.

Consequence: CERTAIN UNDERHOOD FIRES MAY BE CAUSED BY DROPS OF ENGINE OIL, FROM SEEPAGE OR SPILLAGE, BEING DEPOSITED ON THE EXHAUST MANIFOLD THROUGH HARD BRAKING. IF THE MANIFOLD IS HOT ENOUGH AND THE OIL RUNS BELOW THE HEAT SHIELD, IT MAY IGNITE INTO A SMALL FLAME AND, IN SOME INSTANCES, THE FIRE MAY SPREAD TO THE PLASTIC SPARK PLUG WIRE CHANNEL AND BEYOND.

Remedy: DEALERS WILL REPLACE THE ENGINE’S FRONT VALVE COVER AND FRONT-VALVE-COVER GASKET WITH NEW PARTS OF AN IMPROVED DESIGN AND REMOVE THE ENGINE’S PLASTIC COVER AND PLASTIC OIL-FILL-TUBE EXTENSION, ALONG WITH THE 1-3-5 SPARK PLUG WIRE RETAINERS, FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING MAY 2016. , FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING MAY 2016. UNTIL THE REMEDY IS COMPLETED, GM STRONGLY RECOMMENDS THAT OWNERS OBSERVE THE FOLLOWING IMPORTANT PRECAUTIONS (1) THAT OWNERS DO NOT PARK THEIR VEHICLE IN A GARAGE, CAR PORT, OR OTHER STRUCTURE; (2) IF OWNERS NOTICE A BURNING ODOR, THEY SHOULD HAVE THEIR DEALER INSPECT THE VEHICLE. THE DEALER WILL INSPECT THE VEHICLE WITHOUT CHARGE; (3) USE PREMIUM FUEL (91 OCTANE OR HIGHER) IN THE VEHICLE AS RECOMMENDED IN THE VEHICLE'S OWNER MANUAL. OWNERS MAY CONTACT BUICK AT 1-866-608-8080 OR PONTIAC AT 1-800-620-7668, OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .

Reported: 2009-04-08 (April 8, 2009) · Model years: 1997, 1998, 1999, 2000, 2001, 2002, 2003

GENERAL MOTORS IS RECALLING 1,497,516 MY 1997-2003 BUICK REGAL, MY 1998-2003 CHEVROLET LUMINA, MONTE CARLO AND IMPALA, MY 1998-1999 OLDSMOBILE INTRIGUE, MY 1997-2003 PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L V6 NATURALLY ASPIRATED ENGINE. SOME OF THESE VEHICLES HAVE A CONDITION IN WHICH DROPS OF ENGINE OIL MAY BE DEPOSITED ON THE EXHAUST MANIFOLD THROUGH HARD BRAKING.

Consequence: IF THE MANIFOLD IS HOT ENOUGH AND THE OIL RUNS BELOW THE HEAT SHIELD, IT MAY IGNITE INTO A SMALL FLAME AND MAY SPREAD TO THE PLASTIC SPARK PLUG WIRE CHANNEL AND BEYOND INCREASING THE RISK OF AN ENGINE COMPARTMENT FIRE.

Remedy: DEALERS WILL REPLACE THE ENGINE’S FRONT VALVE COVER AND FRONT-VALVE-COVER GASKET WITH NEW PARTS OF AN IMPROVED DESIGN AND REMOVE THE ENGINE’S PLASTIC COVER AND PLASTIC OIL-FILL-TUBE EXTENSION, FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING MAY 2016. OWNERS MAY CONTACT CHEVROLET AT 1-800-630-2438, OLDSMOBILE AT 1-800-630-6537, AND PONTIAC AT 1-800-620-7668 OR HTTP://WWW.PONTIAC.COM OR HTTP:WWW.GMOWNERCENTER.COM.

Reported: 2015-10-26 (October 26, 2015) · Model years: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004

General Motors LLC (GM) is recalling certain model year 1998-1999 Chevrolet Lumina and Oldsmobile Intrigue, 1997-2004 Buick Regal and Pontiac Grand Prix, 2000-2004 Chevrolet Impala, and 1998-2004 Chevrolet Monte Carlo vehicles. The affected vehicles were previously repaired under recalls 08V-118, 09V-116, and 15V-201 to address the possibility that engine oil may drip onto the hot exhaust manifold.

Consequence: Engine oil that drips onto the hot surface of the exhaust manifold may result in a fire.

Remedy: The remedy applied under recalls 08V-118, 09V-116, and 15V-201 did not adequately remove the safety risk. Under the improved remedy, dealers will replace the engine’s front valve cover and gasket. Vehicles that are covered by recalls 08V-118, 09V-116, or 15V-201 that have not yet received the original remedy will instead receive the improved remedy under the original recall number. The recall began on February 19, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020, Buick customer service at 1-800-521-7300, Oldsmobile customer service at 1-800-442-6537 and Pontiac customer service at 1-800-458-8006. GM's number for this recall is 15757. Note: Until the improved remedy has been applied, owners are advised to park their vehicle outside since the fire risk exists even when the vehicle is unattended.

Reported: 1997-11-14 (November 14, 1997) · Model years: 1997

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE RIGHT FRONT BRAKE PIPE CAN CONTACT THE PIOWER STEERING ASSEMBLY CAUSING THE BRAKE LINE TO WEAR THROUGH.

Consequence: THIS CONDITION CAN RESULT IN THE LOSS OF BRAKE FLUID AND EVENTUAL LOSS OF HALF OF THE VEHICLE BRAKE SYSTEM.

Remedy: DEALERS WILL INSPECT FOR PROPER CLEARANCE BETWEEN THE BRAKE LINE AND POWER STEERING ASSEMBLY. ASSEMBLIES FOUND TO BE OUT OF POSITION WILL BE REPOSITIONED AND ALL ASSEMBLIES SECURED TO MAINTAIN PROPER CLEARANCES. ADDITIONALLY, THOSE BRAKE LINES FOUND TO HAVE BEEN DAMAGED WILL BE REPLACED AND PROPERLY ROUTED.

Reported: 1998-05-15 (May 15, 1998) · Model years: 1997, 1998

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE OWNER MANUALS DO NOT CONTAIN THE REQUIREMENT INFORMATION PERTAINING TO THE VEHICLE HEADLAMP AIMING DEVICE. THIS DOES NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT."

Consequence: IF THE HEADLAMP ASSEMBLIES ARE REPLACED, CUSTOMERS MAY NOT BE ABLE TO PROPERLY AIM THE HEADLIGHTS.

Remedy: OWNERS WILL BE MAILED AN OWNER MANUAL'S INSERT WHICH CONTAINS THE APPROPRIATE INFORMATION.

Reported: 1999-12-16 (December 16, 1999) · Model years: 1997

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE WINDSHIELD WIPERS MAY STOP WORKING DUE TO A SEPARATION BETWEEN THE DRIVE PIN AND CRESCENT IN THE CRANK ARM ASSEMBLY.

Consequence: DRIVER VISIBILITY COULD BE REDUCED, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THESE VEHICLES FOR THE PRESENCE OF A PLASTIC WATER DEFLECTOR AND, IF NECESSARY, REPLACE THE WIPER MOTOR CRANK ARM AND INSTALL A WATER DEFLECTOR. ON VEHICLES RECEIVING A REPLACEMENT CRANK ARM AND NEW WATER DEFLECTOR, DEALERS WILL ALSO APPLY ADDITIONAL SEALING MATERIAL TO IMPROVE WATER DEFLECTION AWAY FROM THE CRANK ARM ASSEMBLY AND WILL INSTALL A REINFORCEMENT TO IMPROVE THE PERFORMANCE OF THE WIPER PARK MECHANISM.

Reported: 1999-12-17 (December 17, 1999) · Model years: 1998, 1999

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THESE VEHICLES DO NOT CONFORM TO THE REQUIREMENTS OF FMVSS NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE VERTICAL HEAD LAMP ADJUSTING DEVICE MAY NOT BE CALIBRATED PROPERLY.

Consequence: DRIVER VISIBILITY MAY BE IMPAIRED INCREASING THE RISK OF A CRASH.

Remedy: OWNERS WILL BE PROVIDED WITH AN OWNER'S MANUAL INSERT CONTAINING INSTRUCTIONS FOR OPTICALLY AIMING THE HEADLAMPS.

Reported: 2004-08-10 (August 10, 2004) · Model years: 1999

CERTAIN PASSENGER VEHICLES DO NOT CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." SOME OF THESE VEHICLES DO NOT MEET THE OVERHEAD SIGN ILLUMINATION REQUIREMENTS.

Consequence: LESS ILLUMINATION MAY REDUCE THE ABILITY OF THE DRIVER TO READ OVERHEAD SIGNS WHEN DRIVING AT NIGHT.

Remedy: DEALERS WILL INSTALL NEW LOW BEAM HEADLAMP BULBS IN BOTH OF THE HEADLAMP ASSEMBLIES. THE RECALL BEGAN ON SEPTEMBER 8, 2004. OWNERS SHOULD CONTACT BUICK AT 1-866-608-8080. NOTE: IF THE BULB NEEDS REPLACEMENT IN THE FUTURE, GM BULB NUMBER 89024715 IS AVAILABLE FROM A DEALER, OR THE EQUIVALENT SYLVANIA BULB IS 9006HP, WITH ORANGE LETTERING ON THE BULB.

Reported: 1999-07-09 (July 9, 1999) · Model years: 1999

SOME OF THESE VEHICLES WITH THE KEY IN THE "ON" POSITION, EXHIBIT A CONDITION IN WHICH THE ANTILOCK BRAKE SYSTEM (ABS) MOTOR SHORTS TO ITS CASE AND GROUNDS THROUGH A FLEXIBLE BRAKE FLUID PIPE.

Consequence: THIS SHORT CAN CAUSE EXTREME HEATING OF THE FLEXIBLE BRAKE PIPE WHERE IT CAN MELT A NEARBY FLEXIBLE PLASTIC FUEL HOSE, WHICH COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A GROUND CABLE FROM THE ELECTRONIC BRAKE CONTROL MODULE (EBCM) TO THE ENGINE COMPARTMENT BODY RAIL.

Reported: 2000-05-17 (May 17, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH REAR DRUM BRAKES. THE BOLT HEAD(S) ON THE REAR SPINDLE ROD CAN SEPARATE.

Consequence: THE REAR WHEEL CAN SHIFT, CAUSING REAR STEERING OF THE VEHICLE. THE DRIVER COULD LOSE CONTROL AND A CRASH COULD OCCUR.

Remedy: DEALERS WILL REPLACE THE REAR SPINDLE BOLTS.

Reported: 2000-06-16 (June 16, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE CLAMP THAT SECURES THE FLEXIBLE FUEL FILL HOSE TO THE METAL FILL TUBE MAY BE LOOSE AND COULD SEPARATE.

Consequence: THIS COULD CAUSE FUEL LEAKAGE EXCEEDING THE PERMISSIBLE AMOUNT.

Remedy: DEALERS WILL INSPECT THE FUEL HOSE FILL NECK CLAMP AND, IF NECESSARY, REPOSITION AND TIGHTEN THE CLAMP.

Reported: 2000-08-07 (August 7, 2000) · Model years: 2000, 2001

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL INSPECT THE VEHICLE'S SAFETY BELT BUCKLE ASSEMBLY DATE CODES AND, IF NECESSARY, WILL REPLACE ANY SAFETY BELT BUCKLE ASSEMBLY.

Reported: 2000-11-13 (November 13, 2000) · Model years: 2000, 2001

VEHICLE DESCRIPTION: PASSENGER VEHICLES. SOME OF THESE VEHICLES EXHIBIT A CONDITION IN WHICH THE DRIVER SIDE IMPACT AIR BAG INFLATOR SEPARATES FROM THE AIR BAG MODULE DURING DEPLOYMENT.

Consequence: IF THE INFLATOR SEPARATES, THE AIR BAG WILL NOT DEPLOY PROPERLY DURING A CRASH AND OCCUPANT PROTECTION WOULD BE REDUCED. IF IS ALSO POSSIBLE THAT A SEPARATED INFLATOR COULD BE PROPELLED DOWNWARD AND COULD RESULT IN INJURY TO A REAR SEAT PASSENGER WHOSE FOOT IS POSITIONED APPROXIMATELY UNDER THE INFLATOR MODULE.

Remedy: DEALERS WILL REPLACE THE SIDE IMPACT AIR BAG MODULE.

Reported: 2001-04-06 (April 6, 2001) · Model years: 2000, 2001

VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES, EQUIPPED WITH SUNVISOR LOCATED AIR BAG LABELS, FAIL TO CONFORM TO FEDERAL MOTOR VEHICLES SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THESE VEHICLES HAVE A MESSAGE AREA LESS THAN 30 CM WHICH DOES NOT MEET THE REQUIREMENTS OF THE STANDARD.

Consequence: THESE VEHICLES DO NOT COMPLY WITH THE STANDARD.

Remedy: GM WILL MAIL A NEW BILINGUAL AIR BAG LABEL WITH INSTALLATION INSTRUCTIONS. HOWEVER, THE CUSTOMER MAY BRING THE LABEL TO THEIR DEALER FOR INSTALLATION FREE OF CHARGE. OWNER NOTIFICATION BEGAN MAY 4, 2001. OWNERS WHO DO NOT RECEIVE THE FREE LABEL AND INSTALLATION INSTRUCTIONS WITHIN A REASONABLE TIME SHOULD CONTACT OLDSMOBILE AT 1-800-442-6537 OR BUICK AT 1-800-521-7300.

Reported: 2015-04-06 (April 6, 2015) · Model years: 2004

General Motors LLC (GM) notified the agency on April 2, 2015, that they are is recalling certain model year 2004 Buick Regal vehicles manufactured April 9, 2003, to June 1, 2003, 2004 Chevrolet Impala vehicles manufactured April 8, 2003, to June 23, 2003, and 2004 Chevrolet Monte Carlo vehicles manufactured April 7, 2003, to June 23, 2003. On May 18, 2015, GM expanded the recall to cover an additional 49,751 2004 Pontiac Grand Prix vehicles manufactured January 6, 2003, to June 25, 2004. In the affected vehicles, the valve cover gasket may leak.

Consequence: The leaking engine oil can drip onto the hot surface of the exhaust manifold, increasing the risk of a fire.

Remedy: GM will notify owners, and dealers will remove the plastic cover and plastic oil fill tube extension and replace the front valve cover and gasket. These repairs will be done free of charge. The recall began on April 24, 2015. Owners may contact Buick customer service at 1-800-521-7300, Pontiac customer service at 1-800-762-2737 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is 14574.

Reported: 2012-10-04 (October 4, 2012) · Model years: 2011, 2012, 2013

General Motors LLC (GM) is recalling certain model year 2011-2013 Buick Regal and model year 2013 Chevrolet Malibu vehicles. These vehicles are equipped with two turn signal bulbs in each front turn signal. If one of the two front turn signal bulbs burn out in either front turn signal lamp, there is no indication to the driver. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment."

Consequence: If the driver is not aware that a turn signal is not functioning properly, the driver may continue to drive the vehicle. If half of a front turn signal is not illuminating, other driver's may not be aware that the affected vehicle is turning, thereby increasing the risk of a crash.

Remedy: GM will notify owners, dealers will update the body control module software, free of charge. The recall began in September 2014. Owners may contact Buick at 1-800-521-7300 or Chevrolet at 1-800-222-1020. GM's number for this recall is 12212.

Reported: 2014-07-23 (July 23, 2014) · Model years: 2011, 2012

General Motors LLC (GM) is recalling certain model year 2011-2012 Buick LaCrosse, Regal and Chevrolet Camaro, as well as certain 2010-2012 Cadillac SRX, Chevrolet Equinox and GMC Terrain vehicles, equipped with power height adjustable driver and passenger seats. In the affected vehicles, the bolt that secures the driver's and passenger's power front seat height adjuster may fall out causing the seat to drop suddenly to the lowest vertical position.

Consequence: If the driver's seat unexpectedly drops, the distraction and altered seat position may affect the drivers' control of the vehicle, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will replace the height adjuster shoulder bolts, free of charge. The manufacturer distributed interim letters to owners on September 11, 2014. The recall began on December 26, 2014. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-8006 (Cadillac), 1-800-222-1020 (Chevrolet), or 1-800-462-8782 (GMC). GM's number for this recall is 14271.

Reported: 2016-07-05 (July 5, 2016) · Model years: 2011

General Motors LLC (GM) is recalling certain model year 2016-2017 Buick Verano and 2016 Chevrolet Malibu as the electronic park lock lever may allow the ignition key to be removed without the transmission being in PARK. Also, certain 2013 Buick Encore, 2011 Buick Regal, 2013-2014 Buick Verano, 2011-2016 Chevrolet Cruze, 2010-2013 Chevrolet Equinox 2013-2015 Chevrolet Malibu, and 2011-2013 GMC Terrain vehicles may have been serviced with similar defective replacement electronic park lock levers. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 114, "Theft Protection and Rollaway Prevention."

Consequence: If the key is removed without the transmission in PARK, the vehicle may rollaway as occupants are exiting, increasing the risk of injury.

Remedy: GM will notify owners, and dealers will inspect and if necessary replace the key cylinder lock housing, free of charge. The recall began on October 14, 2016. Owners may contact Chevrolet customer service at 1-800-222-1020, Buick 1-800-521-7300, and GMC 1-800-462-8782. GM's number for this recall is 50490 and 50491.

Reported: 2016-07-07 (July 7, 2016) · Model years: 2011

General Motors LLC (GM) is recalling certain model year 2011 Buick Regal vehicles manufactured November 3, 2009, to March 25, 2011, equipped with 8-way power adjustable front seats. The power seat wiring harness may contact the seat frame, causing the wires to chafe.

Consequence: Chafed harness wires may cause a short circuit, increasing the risk of a fire.

Remedy: GM will notify owners, and dealers will inspect and secure the wiring harness, and repair any chafed wires as necessary, free of charge. The recall began on March 13, 2017. Owners may contact Buick customer service at 1-800-521-7300. GM's number for this recall is 30710.

Reported: 2012-03-07 (March 7, 2012) · Model years: 2012

GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2012 BUICK REGAL VEHICLES MANUFACTURED FROM FEBRUARY 22, 2011, THROUGH FEBRUARY 22, 2012 FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108 “LAMPS, REFLECTIVE DEVICES AND ASSOCIATED EQUIPMENT.” DUE TO A SOFTWARE ERROR, THE PARKING LAMPS DO NOT ACTIVATE WHEN EITHER THE PARKING LAMPS OR HEADLAMPS ARE TURNED ON.

Consequence: INADEQUATE LIGHTING COULD REDUCE THE VISIBILITY OF THE VEHICLE, INCREASING THE POTENTIAL FOR A CRASH.

Remedy: GENERAL MOTORS WILL NOTIFY OWNERS, AND DEALERS WILL REPROGRAM THE BODY CONTROL MODULE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 29, 2012. OWNERS MAY CONTACT GM AT 1-800-521-7300.

Reported: 2013-05-06 (May 6, 2013) · Model years: 2012, 2013

General Motors (GM) is recalling certain model year 2012 and 2013 Buick LaCrosse and Regal, and model year 2013 Chevrolet Malibu Eco vehicles equipped with eAssist. These vehicles may have a condition in which the Generator Control Module (GCM) may not function properly. This could cause a gradual loss of battery charge and the illumination of the malfunction indicator light.

Consequence: If the vehicle is continued to be driven, the engine may stall and/or the vehicle may not start. In addition, there may be a burning or melting odor, smoke, and possibly a fire in the trunk.

Remedy: GM will notify owners and dealers will test the GCM and replace it, as necessary, free of charge. The recall began on June 11, 2013. Owners may contact GM at 1-800-521-7300. GM's recall campaign number is 13136.

Reported: 2020-12-21 (December 21, 2020) · Model years: 2012, 2013

General Motors, LLC (GM) is recalling certain 2012-2013 Buick Regal, 2013 Chevrolet Malibu, and 2010-2013 Buick Lacrosse vehicles sold or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin. These vehicles may have rear toe links that received excessive electrocoating (e-coat) corrosion protection, which could cause the e-coat to become brittle and break away when contacted by road debris. Over time, the e-coat may chip away, exposing the metal toe link and making it more susceptible to corrosion. Corrosion may eventually cause the toe link to thin and ultimately to fracture.

Consequence: A rear toe link fracture may reduce the driver's ability to control the vehicle, increasing the risk of a crash.

Remedy: GM will notify owners, and dealers will replace the rear suspension toe links and adjuster fasteners free of charge. Parts are not currently available. Owners were mailed an interim notification on January 27, 2021, and April 15, 2021. A third notification was mailed on August 19, 201. Owners may contact Buick customer service at 1-800-521-7300 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202308930.

Reported: 2021-12-22 (December 22, 2021) · Model years: 2012, 2013

General Motors, LLC (GM) is recalling certain 2010-2013 Buick Lacrosse, 2012-2013 Buick Regal, and 2013 Chevrolet Malibu vehicles sold or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin. These vehicles may have rear toe links that received an improper amount of electrocoating (e-coat) corrosion protection, which could cause the e-coat to become brittle and break away when contacted by road debris. Over time, the e-coat may chip away, exposing the metal toe link and making it more susceptible to corrosion. Corrosion may eventually cause the toe link to thin and ultimately fracture.

Consequence: A rear toe link fracture may reduce the driver's ability to control the vehicle, increasing the risk of a crash.

Remedy: Dealers will replace the rear suspension toe links and adjuster fasteners, free of charge. Owner notification letters were mailed January 27, 2022. Owners may contact Buick customer service at 1-800-521-7300 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N212346640. This recall is an expansion of NHTSA recalls 20V-764 and 21V-633.

Reported: 2026-02-26 (February 26, 2026) · Model years: 2012, 2013

General Motors, LLC (GM) is recalling certain 2012–2013 Buick Regal Turbo and GS trim-level vehicles that were sold or ever registered, in Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin. The rear suspension toe links may have received improper corrosion protection, which can result in rear toe link fracture.

Consequence: Rear toe link fracture can cause a loss of vehicle control, increasing the risk of a crash.

Remedy: Dealers will replace the rear suspension toe links and adjuster fasteners, free of charge. Owner notification letters were mailed April 3, 2026. Owners may contact Buick customer service at 1-800-521-7300. GM's number for this recall is N252537580. This recall expands previous NHTSA recall numbers 20V764, 21V633, and 21V00F.

Reported: 2021-08-12 (August 12, 2021) · Model years: 2013

General Motors, LLC (GM) is recalling certain 2013 Buick Regal, Chevrolet Malibu, and Buick Lacrosse vehicles sold or ever registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, or Wisconsin. These vehicles may have rear toe links that received excessive electrocoating (e-coat) corrosion protection, which could cause the e-coat to become brittle and break away when contacted by road debris. Over time, the e-coat may chip away, exposing the metal toe link and making it more susceptible to corrosion. Corrosion may eventually cause the toe link to thin and ultimately fracture.

Consequence: A rear toe link fracture may reduce the driver's ability to control the vehicle, increasing the risk of a crash.

Remedy: Dealers will replace the rear suspension toe links and adjuster fasteners, free of charge. Interim owner notification letters were mailed on September 30, 2021. Owner notification letters were mailed on January 3, 2022. Owners may contact Buick customer service at 1-800-521-7300 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N212330130.

Reported: 2014-02-21 (February 21, 2014) · Model years: 2014

General Motors LLC (GM) is recalling certain model year 2014 Buick Regal, LaCrosse, Verano, and Enclave, and Chevrolet Impala, Malibu, Cruze, and Traverse, and GMC Acadia vehicles equipped with automatic transmissions. In the affected vehicles, the transmission shift cable adjuster may disengage from the transmission shift lever. As such, these vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 102, "Transmission Shift Lever Sequence, Starter Interlock, and Transmission Braking Effect." They also fail to conform to FMVSS number 114, "Theft Protection and Rollaway Prevention."

Consequence: If a vehicle's shift cable disengages from the transmission shift lever, a driver may be unable to shift gear positions and the indicated shift position may not represent the gear position the vehicle is in. Should a disengagement occur while the vehicle is being driven, when the driver goes to stop and park the vehicle, the driver may be able to shift the lever to the "PARK" position, but the vehicle transmission may not be in the "PARK" gear position. If the vehicle is not in the "PARK" position there is a risk the vehicle will roll away as the driver and other occupants exit the vehicle or anytime thereafter. A vehicle rollaway increases the risk of injury to exiting occupants and bystanders.

Remedy: General Motors will notify owners, and dealers will inspect and replace any affected transmission shift cable adjusters, free of charge. The recall began on April 10, 2014. Chevrolet owners may contact General Motors at 1-800-222-1020, Buick owners at 1-800-521-7300, and GMC owners at 1-800-462-8782. General Motors' number associated with this recall is 14048.

Reported: 2014-07-02 (July 2, 2014) · Model years: 2014

General Motors LLC (GM) is recalling certain model year 2014 Buick Regal, Cadillac XTS, Chevrolet Camaro and Chevrolet Impala vehicles. Improperly torqued fasteners may cause the steering intermediate shaft and the steering gear and/or the lower control arm and the lower ball joint to separate.

Consequence: If any of the components separate, the vehicle may have a loss of steering, increasing the risk of a crash.

Remedy: GM began to notify owners on June 27, 2014, and dealers will inspect the fasteners for correct torque, correcting them as necessary, free of charge. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-8006 (Cadillac) or 1-800-222-1020 (Chevrolet). GM's number for this recall is 14378.

Reported: 2016-02-24 (February 24, 2016) · Model years: 2016

General Motors LLC (GM) is recalling certain model year 2016 Buick Regal Vehicles manufactured August 30, 2015, to February 12, 2016. The affected vehicles have a power-steering assist system that may fail.

Consequence: A loss of power steering assist may increase the risk of a crash.

Remedy: GM will notify owners, and dealers will replace the electric belt drive rack and pinion steering gear assembly, free of charge. The recall began on March 21, 2016. Owners may contact Buick customer service at 1-800-521-7300. GM's number for this recall is 21510.

Reported: 2018-04-12 (April 12, 2018) · Model years: 2018

General Motors LLC (GM) is recalling certain 2018 Buick Regal vehicles. During the manufacturing process, the rear seat belts may have been improperly routed around the bolster bracket on the rear outboard seats, which can cause inadequate restraint of the passengers.

Consequence: If the seat belt fails to adequately restrain the passengers in a crash, it can increase the risk of injury.

Remedy: GM will notify owners, and dealers will inspect the rear outboard seat belts, correcting the routing of the seat belts as necessary, free of charge. The recall began May 14, 2018. Owners may contact Buick customer service at 1-800-521-7300. GM's number for this recall is 18117.

Reported: 2018-08-30 (August 30, 2018) · Model years: 2018, 2019

General Motors LLC (GM) is recalling certain 2018-2019 Chevrolet Equinox, Impala, Cruze, Volt and Bolt EV vehicles, GMC Terrain vehicles, Buick Lacrosse and Regal vehicles, Cadillac XTS and XTS Professional vehicles and 2018 Chevrolet Malibu vehicles. The rear brake caliper pistons may have an insufficient coating causing gas pockets to form, potentially reducing rear brake performance.

Consequence: A reduction of braking performance can increase the risk of a crash.

Remedy: GM will notify owners, and dealers will bleed the vehicle's brake system, free of charge. The recall began October 11, 2018. Owners may contact Buick customer service at 1-800-521-7300, Cadillac customer service at 1-800-458-8006, Chevrolet customer service at 1-800-222-1020, or GMC customer service at 1-800-462-8782. GM's number for this recall is 18279.

Reported: 2022-06-30 (June 30, 2022) · Model years: 2018, 2019, 2020

General Motors, LLC (GM) is recalling certain 2018-2020 Buick Regal vehicles. In the event of a vacuum-power brake assist failure, a software error in the electronic brake control module (EBCM) may result in a loss of power brake assist. As such, these vehicles fail to conform to Federal Motor Vehicle Safety Standard No. 135, "Light vehicle brake systems."

Consequence: A loss of power brake assist can extend the distance required to stop the vehicle, increasing the risk of a crash.

Remedy: Dealers will update the EBCM software, free of charge. Interim owner notification letters advising owners of the safety risk were mailed on August 19, 2022. Owner notification letters were mailed September 16, 2022. Owners may contact Buick's customer service at 1-800-521-7300.

Reported: 2019-10-24 (October 24, 2019) · Model years: 2019, 2020

General Motors LLC (GM) is recalling certain 2019-2020 Buick Regal vehicles. The driver or passenger front seat frames may have a lower crossbar that was improperly welded.

Consequence: Seats with improper welds may not provide adequate protection in the event of a crash, increasing the risk of an injury.

Remedy: GM will notify owners, and dealers will inspect the crossbar welds on the front seats. If the crossbar is improperly welded, the seat back frame will be replaced, free of charge. Interim notices informing owners of the safety risk were mailed November 26, 2019. Owners received a second notice and the recall began February 20, 2020. Owners may contact Buick customer service at 1-800-521-7300. GM's number for this recall is N192278300.