Chevrolet C30 recalls by model year

Reported: 1967-01-23 (January 23, 1967) · Model years: 1967

Reported: 1970-09-08 (September 8, 1970) · Model years: 1970

Reported: 1970-10-21 (October 21, 1970) · Model years: 1971

Reported: 1970-12-10 (December 10, 1970) · Model years: 1971

Reported: 1971-03-24 (March 24, 1971) · Model years: 1971

Reported: 1973-11-01 (November 1, 1973) · Model years: 1973

Reported: 1974-05-17 (May 17, 1974) · Model years: 1974

Reported: 1975-09-03 (September 3, 1975) · Model years: 1975

Reported: 1977-06-22 (June 22, 1977) · Model years: 1975, 1976

THE FRONT SUSPENSION CONTROL ARMS WERE ASSEMBLED WITH BALL JOINTS WHICH MAY CONTAIN SOCKETS THAT WERE NOT PROPERLY HEAT-TREATED. THIS MAY CAUSE THE SOCKET TO WEAR RAPIDLY AND ALLOW THE BALL JOINT STUD TO SEPARATE FROM THE SOCKET, CAUSING EITHER THE LEFT OR RIGHT WHEEL SUSPENSION TO COLLAPSE.

Remedy: DEALER WILL INSPECT AND, WHERE NECESSARY, WILL REPLACE THE BALL JOINTS WITHOUT CHARGE TO OWNER.

Reported: 1975-12-19 (December 19, 1975) · Model years: 1976

Reported: 1977-10-14 (October 14, 1977) · Model years: 1976, 1977

THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVER"S FOOT IS REMOVED FROM THE PEDAL.

Remedy: DEALER WILL INSTALL A NEW ACCELERATOR PEDAL AND RETAINER DESIGNED TO PREVENT THE ACCELERATOR PEDAL ROD FROM CUTTING THE RUBBER MAT OR CARPET. THIS WILL BE PERFORMED WITHOUT CHARGE.

Reported: 1977-08-10 (August 10, 1977) · Model years: 1977

ON THE INVOLVED VEHICLES, THE NUTS WHICH ATTACH THE BRAKE MASTER CYLINDER TO THE HYDRO-BOOST UNIT MAY HAVE BEEN OVER-TIGHTENED. THIS COULD HAVE CAUSED STRIPPED THREADS AND CRACKED ATTACHING FLANGES. SHOULD THESE NUTS FAIL, THE PARTS MAY SEPARATE AND LOSS OF SERVICE BRAKES WOULD RESULT.

Remedy: DEALER WILL INSPECT FOR CRACKS IN THE ATTACHING FLANGES; UNITS WITH CRACKS PRESENT WILL BE REPLACED. IF NO CRACKS ARE FOUND, THE STUDS WILL BE REMOVED AND THE HOLES DRILLED OUT. THE UNIT WILL BE REASSEMBLED USING BOLTS AND NUTS IN PLACE OF THE EXISTING STUDS.

Reported: 1978-06-01 (June 1, 1978) · Model years: 1978

THE LEFT AND RIGHT FRONT SUSPENSION CROSSMEMBER STRUT RODS, WHICH GIVE ADDED STRENGTH, MAY HAVE BEEN OMITTED DURING ASSEMBLY. CONSEQUENTLY, A FRAME CROSSMEMBER CRACK COULD EVENTUALLY DEVELOP AT THE FORWARD VERTICAL FRONT SUSPENSION BOLT.

Remedy: DEALER WILL INSTALL THE NECESSARY FRONT LEFT AND RIGHT RODS WITHOUT CHARGE TO OWNER.

Reported: 1979-01-16 (January 16, 1979) · Model years: 1979

THE FRONT HOSES ON THE INVOLVED VEHICLES MAY HAVE IMPROPERLY ORIENTED HOSE FITTINGS, RESULTING IN A RUBBING CONTACT BETWEEN THE RIGHT BRAKE HOSE AND THE UPPER CONTROL ARM OF THE FRONT SUSPENSION OR IN A TWISTED LEFT HOSE RESULTING IN A FAULTY ATTACHMENT AT THE FRAME FITTING. SHOULD EITHER OF THESE CONDITIONS EXIST, THEY COULD EVENTUALLY RESULT IN BRAKE HOSE FAILURE CAUSING LOSS OF BRAKE FLUID AND CONSEQUENT LOSS OF THE FRONT BRAKING ACTION.

Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, REPLACE ONE OR BOTH FRONT BRAKE HOSES AT NO COST TO OWNER.

Reported: 1979-06-06 (June 6, 1979) · Model years: 1979

ON THE INVOLVED VEHICLES THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH WHICH IS OPERATED BY THE BRAKE PEDAL MAY HAVE BEEN ASSEMBLED WITH AN INCORRECT LUBRICANT ON THE ACTUATING PLUNGER. THIS CAN CAUSE THE REAR BRAKE STOPLIGHTS TO BECOME INOPERATIVE AND THE CRUISE CONTROL, IF ACTIVATED, TO STAY ELECTRICALLY ENGAGED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE BRAKE STOPLIGHT AND CRUISE CONTROL SWITCH AT NO COST TO OWNER.

Reported: 1981-01-13 (January 13, 1981) · Model years: 1979, 1980

FATIGUE CRACKS MAY DEVELOP IN THE BRAKE VACUUM BOOSTER HOUSING. THIS MAY CAUSE A VACUUM LEAK AND REDUCE THE EFFECTIVENESS OF THE BRAKES. AFTER PROLONGED USE, THE CRACKS MAY DEVELOP TO THE EXTENT THAT THE BOOSTER MAY SEPARATE FROM THE VEHICLE.

Remedy: VEHICLES WILL BE INSPECTED FOR FATIGUE CRACKS IN THE BRAKE VACUUM BOOSTER. THOSE WITHOUT CRACKS WILL HAVE A SUPPORT BRACE INSTALLED. THOSE WITH EVIDENCE OF CRACKING WILL HAVE A NEW BRAKE VACUUM BOOSTER AND SUPPORT BRACE INSTALLED. THIS SERVICE WILL BE PROVIDED AT NO CHARGE.

Reported: 1984-03-20 (March 20, 1984) · Model years: 1984

THE FRONT STEERING ALIGNMENT MAY NOT HAVE BEEN COMPLETED. THE TIE RODS, A PART OF THE STEERING LINKAGE WHICH TRANSMITS STEERING MOVEMENTS TO THE WHEELS, MAY NOT HAVE BEEN FASTENED COMPLETELY. THE ALIGNMENT OF THE STEERING WILL AFFECT THE VEHICLE"S HANDLING PROPERTIES. INCOMPLETE FASTENING OF THE STEERING TIE ROD MAY LEAD TO COMPLETE SEPARATION OF THE LINKAGE.

Remedy: TIE ROD CLAMP FASTENERS WILL BE INSPECTED. IF NECESSARY, THE TOE-IN WILL BE SET, AND THE TIE ROD CLAMP FASTENERS WILL BE TIGHTENED. THERE WILL BE NO CHARGE FOR THESE SERVICES.

Reported: 1984-10-26 (October 26, 1984) · Model years: 1984, 1985

IN SOME 16 X 6 DISC WHEELS A MANUFACTURING DEFECT MAY CAUSE THE WHEELS TO CRACK IN THE DROP CENTER PORTION OF THE RIM. IF THE CRACK WERE TO OCCUR ON A WHEEL WITH A TUBE TYPE TIRE MOUNTED TO IT, AND CONTINUED TO GO UNDETECTED, THE WHEEL COULD SPLIT, RESULTING IN A RAPID LOSS OF AIR FROM THE TIRE.

Remedy: THE DEALER WILL INSPECT EACH WHEEL AND REPLACE IT IF NECESSARY, WITHOUT CHARGE.

Reported: 1987-01-20 (January 20, 1987) · Model years: 1984, 1985, 1986

TRUCKS FAILED TO COMPLY WITH REQUIREMENTS OF FMVSS 301, FUEL SYSTEM INTEGRITY, DURING A 30 MPH FRONTAL BARRIER TEST.

Consequence: GREATER THAN ACCEPTABLE FUEL SPILLAGE DURING AND AFTER ACOLLISION COULD RESULT IN A FIRE.

Remedy: INSTALL AN ADDITIONAL SHIELD TO THE FRONT OF THE ORIGINAL SHIELD TO PROTECT THE FUEL TANK.

Reported: 1985-11-26 (November 26, 1985) · Model years: 1985

THE WHEEL MAY DEVELOP CRACKS BETWEEN THE DISC AND RIM. CONSEQUENCE OF DEFECT: IF THIS OCCURS AND IS NOT NOTICED, THE CRACK COULD INCREASE AROUND THE RIM, RESULTING IN SEPARATION OF THE RIM FROM THE DISC, LOSS OF CONTROL AND AN ACCIDENT MAY OCCUR.

Remedy: REPLACE WHEELS HAVING THE SUSPECTED MANUFACTURING CODE NUMBER.

Reported: 1991-12-13 (December 13, 1991) · Model years: 1985, 1986

THE LEFT HAND LOWER CONTROL ARM CAN CRACK STARTING AT THE REAR FLANGE AND PROGRESSING TO THE BALL JOINT MOUNTING HOLE AND EVENTUALLY CAUSE THE LOWER BALL JOINT TO SEPARATE FROM THE CONTROL ARM.

Consequence: IF THE BALL JOINT SEPARATES FROM THE CONTROL ARM, A LOSSOF VEHICLE CONTROL COULD RESULT IN A VEHICLE CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A RESINFORCED BRACE TO THE LEFT HAND LOWER CONTROL ARM.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

CRUISE CONTROL CABLE LOCK MECHANISM MAY SELF DISENGAGE CAUSING ERRATIC OPERATION OR THROTTLE NOT RETURNING TO IDLE.

Consequence: ENGINE SPEED WOULD NOT DECREASE; LOSS OF ACCELERATORCONTROL COULD RESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A CLAMP AROUND THE LOCK TAB OF CRUISE CONTROL.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

TRUCKS MAY HAVE CRACKED OR BROKEN DOOR STRIKER NUTS, WHICH DO NOT CONFORM TO FMVSS 206.

Consequence: IN A COLLISION, CRACKED OR BROKEN STRIKER NUT COULDALLOW DOOR TO OPEN UNEXPECTEDLY AND POSSIBLY CAUSE INJURY TO OCCUPANTS.

Remedy: REPLACE EXISTING DOOR STRIKER NUTS.

Reported: 1993-02-01 (February 1, 1993) · Model years: 1988, 1989, 1990, 1991, 1992, 1993

UNANTICIPATED HEAT IN THE TRANSMISSION CAN FORCE THE TRANSMISSION FLUID OUT OF THE VENT TUBE.

Consequence: THE VENTED TRANSMISSION FLUID CAN CATCH FIRE IF EXPOSEDTO A SOURCE OF IGNITION.

Remedy: INSTALL A LONGER TRANSMISSION VENT HOSE ROUTED TO THE LEFT SIDE OF THE ENGINE COMPARTMENT OF THE VEHICLE.

Reported: 1989-05-15 (May 15, 1989) · Model years: 1989

THERE MAY BE BELOW SPECIFIED TORQUE ON THE TRAILER HITCH ATTACHING FASTENERS, ALLOWING THE TRAILER HITCH TO MOVE UNDER TOWING LOADS.

Consequence: FASTENERS COULD FAIL; IF THIS OCCURS WHILE TRAILERIS BEING PULLED, HITCH AND TRAILER COULD SEPARATE AND A VEHICLE CRASH COULDOCCUR WITHOUT PRIOR WARNING.

Remedy: CORRECT TORQUE IN TRAILER HITCH FASTENERS TO PREVENT TRAILER SEPARATION.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1990-06-04 (June 4, 1990) · Model years: 1990

LOOSE PIVOT BOLT HOLDING THE BRAKE PEDAL TO ITS SUPPORT BRACKET COULD DISENGAGE FROM THE NUT.

Consequence: THIS COULD CAUSE LOSS OF BRAKING ACTIVITY THAT COULDRESULT IN A TRUCK CRASH WITHOUT PRIOR WARNING.

Remedy: RETORQUE BRAKE PEDAL PIVOT BOLTS TO SPECIFICATIONS TO PREVENT LOOSENING.

Reported: 1992-03-24 (March 24, 1992) · Model years: 1991

THERE MAY BE FATIGUE FRACTURES OF THE TIE ROD THROUGH THE DAMPER STUD MOUNTING HOLE.

Consequence: TIE ROD FRACTURES RESULT IN LOSS OF STEERING CONTROL ANDTHE POSSIBILITY OF A VEHICLE CRASH.

Remedy: REPLACE THE EXISTING TIE ROD ASSEMBLY, DAMPER, AND DAMPER BRACKET WITH NEWLY DESIGNED PARTS.

Reported: 1999-05-20 (May 20, 1999) · Model years: 1992

VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.

Reported: 1993-09-27 (September 27, 1993) · Model years: 1993

THE REAR BENCH SEAT DOES NOT MEET THE LOAD REQUIREMENTS OF FMVSS 207, "SEATING SYSTEMS," BECAUSE THE MANUAL LATCH MECHANISM ON THE FOLDING FULL BENCH REAR SEAT WAS ATTACHED TO THE BACK FRAME LOWER CROSS TUBE WITH DOMED HEAD STEEL RIVETS INSTEAD OF THE BOLTS SPECIFIED.

Remedy: THE RIVETS MUST BE REPLACED WITH THE CORRECT BOLTS.

Reported: 1995-12-21 (December 21, 1995) · Model years: 1993, 1994

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1993-09-15 (September 15, 1993) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993) · Model years: 1994

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1994

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

Consequence: IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

Remedy: DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

Reported: 1995-12-13 (December 13, 1995) · Model years: 1994, 1995

THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

Reported: 1999-02-05 (February 5, 1999) · Model years: 1994

VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

Consequence: THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.

Reported: 1995-02-16 (February 16, 1995) · Model years: 1995

DUE TO A THIN CASE CASTING, AN EXTERNAL TRANSMISSION LEAK CAN OCCUR.

Consequence: THIS CONDITION CAN CAUSE TRANSMISSION OIL TO SPRAYONTO THE EXHAUST SYSTEM AND RESULT IN A POSSIBLE VEHICLE FIRE.

Remedy: DEALERS WILL INSPECT THE TRANSMISSION CASE ASSEMBLY FOR THE INVOLVED CASE CASTING. IF THE ASSEMBLY IS INVOLVED, THE TRANSMISSION WILL BE REPLACED.

Reported: 1996-01-02 (January 2, 1996) · Model years: 1995

THE STEERING COLUMN UPPER INTERMEDIATE-SHAFT NUT MAY NOT BE TORQUED TO PROPER SPECIFICATIONS. THE NUT COULD LOOSEN AND DETACH ALLOWING THE THROUGH-BOLT THAT SECURES THE UPPER INTERMEDIATE-SHAFT TO THE LOWER STEERING COLUMN SHAFT JOINT TO FALL OUT.

Consequence: THIS LOOSE ENGAGEMENT CAN PROVIDE NOTICEABLE NOISE AND ABNORMAL STEERING FEELING TO THE DRIVER AND, IF LEFT UNATTENDED, THE STEERING SHAFTS CAN SEPARATE RESULTING IN A LOSS OF STEERING CONTROL.

Remedy: DEALERS WILL TORQUE THE SUSPECT FASTENERS TO THE PROPER SPECIFICATIONS.

Reported: 1996-04-04 (April 4, 1996) · Model years: 1995, 1996

THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, "ACCELERATOR CONTROL SYSTEMS."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE ENGINE SPEED MAY NOT RETURN TO IDLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT FOR ADEQUATE THROTTLE CABLE TO DASH MAT CLEARANCE, AND IF THERE IS INSUFFICIENT CLEARANCE, CUT OUT A PORTION OF THE DASH MAT TO PROVIDE PROPER CLEARANCE.

Reported: 1996-07-01 (July 1, 1996) · Model years: 1995, 1996

THESE TIRES HAVE BEAD DAMAGE WHICH OCCURED DURING TIRE MOUNTING.

Consequence: THIS DAMAGE TO THE TIRE REINFORCING STRUCTURE IN THE BEAD "TOE" AREA CAUSES A BULGE IN THE SIDEWALL AFTER THE TIRE IS INFLATED. THIS CONDITION WILL RESULT IN A SLOW AIR LOSS CAUSING THE TIRE TO GO FLAT. HOWEVER, IT IS POSSIBLE FOR THE DAMAGE TO RESULT IN A RAPID AIR LOSS CAUSING INJURIES TO ANYONE IF THEY WERE HANDLING THE TIRE WHEN THIS OCCURRED.

Remedy: DEALERS WILL DEMOUNT EACH TIRE AND INSPECT FOR BEAD DAMAGE. IF BEAD DAMAGE IS FOUND, THE TIRE WILL BE REPLACED.

Reported: 1997-03-07 (March 7, 1997) · Model years: 1995, 1996, 1997

VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.

Consequence: THIS PINCHING CAN CUT THE HAND OR POSSIBLY SEVER THE FINGER(S) WITHOUT PRIOR WARNING.

Remedy: DEALERS WILL INSTALL A PROTECTOR COVER OVER THE RECLINER MECHANISM.

Reported: 1995-12-28 (December 28, 1995) · Model years: 1996

CERTAIN TRUCKS HAVE FUEL RAIL ASSEMBLIES WITH AN IMPROPERLY CRIMPED END RETAINER CLIP THAT RESULTS IN A FUEL LEAK.

Consequence: IF FUEL LEAKAGE OCCURS AND AN IGNITION SOURCE IS PRESENT, AN ENGINE COMPARTMENT FIRE COULD OCCUR.

Remedy: DEALERS WILL INSPECT THE FUEL RAIL ASSEMBLY AND REPLACE ANY FUEL RAIL ASSEMBLY WITH A JULIAN DATE CODE OF 95318 THROUGH 95338.

Reported: 1996-05-07 (May 7, 1996) · Model years: 1996

THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.

Consequence: VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.

Reported: 1998-02-17 (February 17, 1998) · Model years: 1998

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND MULTI-PURPOSE PASSENGER VEHICLES. ONE OR BOTH FRONT BRAKE ROTOR/HUBS WERE BUILT WITH AN OUT-OF-SPECIFICATION GRAY IRON THAT CAN FAIL DURING THE LIFE OF THE VEHICLE.

Consequence: IF A DRIVER CONTINUES TO DRIVE WITH A CRACKED ROTOR, THE CRACKS COULD CONTINUE AROUND THE WHEEL MOUNTING BOLT CIRCLE AND ULTIMATELY RESULT IN A WHEEL SEPARATION.

Remedy: DEALERS WILL INSPECT THE ROTORS FOR A CORE DATE OF "287" AND, IF FOUND, REPLACE THE ROTOR.