1994 Chevrolet C30: complaints, problems and recalls

ELECTRONIC DIESEL INJECTION PUMP FAILURE AND REPLACEMENT 09/29/97 MILAGE 64073 ELECTRONIC DIESEL INJECTION PUMP FAILURE AND REPLACEMENT 04/30/98 MILAGE 77903 ELECTRONIC DIESEL INJECTION PUMP FAILURE AND REPLACEMENT 06/01/99 MILAGE 87194. *AK ELECTRONIC DIESEL INJECTION PUMP FAILURE AND REPLACEMENT 03/28/01 MILAGE 108155 ELECTRONIC DIESEL INJECTION PUMP FAILURE 05/19/03 MILAGE 142716

Owner-reported narrative. 64,073 miles reported. Look up ODI 10025795 at NHTSA ↗

RIGHT REAR BRAKE LINE BROKE WHERE BRAKE LINE ENTERS RIGHT WHEEL CYLINDER, PREVENTING VEHICLE FROM STOPPING/BRAKE FLUID LEAK.

Owner-reported narrative. Look up ODI 507296 at NHTSA ↗

ANY KIND OF WEATHER WHEN BRAKES ARE APPLIED, THE LOCK UP . *AK

Owner-reported narrative. Look up ODI 807400 at NHTSA ↗

WHILE DRIVING AT ANY SPEED THE VEHICLE JUST QUITS WITHOUT ANY KIND OF WARNING AT ALL. THE FUEL INJECTION PUMP HAS BEEN REPLACED (6) TIMES SINCE OCTOBER OF 96 BECAUSE OF THIS PROBLEM. THIS HAS NOT CORRECTED THE PROBLEM.

Owner-reported narrative. Look up ODI 812801 at NHTSA ↗

BRAKES LOCKED UP AND TRUCK SLID ON THE ROAD IN THE RAIN. *AK

Owner-reported narrative. Look up ODI 818192 at NHTSA ↗

ABS, WHEN BRAKES ARE APPLIED VEHICLE WILL STEER VERY HARD TO LEFT, ALSO WEARING THE BRAKES PADS IN FRONT. TT

Owner-reported narrative. Look up ODI 967791 at NHTSA ↗

THE TAIL GATE KEEP OPEN UP . TT

Owner-reported narrative. Look up ODI 969618 at NHTSA ↗

Reported: 1993-09-15 (September 15, 1993)

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993)

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994)

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1995-12-13 (December 13, 1995)

IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.

Consequence: IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.

Remedy: DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

Reported: 1995-12-13 (December 13, 1995)

THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

Reported: 1995-12-21 (December 21, 1995)

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1999-02-05 (February 5, 1999)

VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.

Consequence: THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.

Remedy: DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.