Chevrolet K10 recalls by model year

Reported: 1967-01-23 (January 23, 1967) · Model years: 1967

Reported: 1970-04-03 (April 3, 1970) · Model years: 1969

Reported: 1971-08-19 (August 19, 1971) · Model years: 1969, 1970, 1971

Reported: 1970-08-10 (August 10, 1970) · Model years: 1970

Reported: 1971-07-20 (July 20, 1971) · Model years: 1971

Reported: 1971-10-13 (October 13, 1971) · Model years: 1972

Reported: 1973-10-03 (October 3, 1973) · Model years: 1973

Reported: 1974-02-15 (February 15, 1974) · Model years: 1973, 1974

Reported: 1974-04-25 (April 25, 1974) · Model years: 1974

Reported: 1977-10-14 (October 14, 1977) · Model years: 1976, 1977

THE ACCELERATOR PEDAL ROD IN COMBINATION WITH THE PEDAL INSTALLED ON THE INVOLVED VEHICLES MAY CUT THROUGH THE FLOOR PAN RUBBER MAT OR CARPET INTO THE THICK RESILIENT INSULATION PAD UNDERNEATH DURING HEAVY OR REPEATED FULL THROTTLE APPLICATIONS. AS A RESULT, THE ACCELERATOR PEDAL ROD MAY CATCH IN THE MAT OR CARPET, PREVENTING THE THROTTLE FROM RETURNING TO IDLE WHEN THE DRIVER"S FOOT IS REMOVED FROM THE PEDAL.

Remedy: DEALER WILL INSTALL A NEW ACCELERATOR PEDAL AND RETAINER DESIGNED TO PREVENT THE ACCELERATOR PEDAL ROD FROM CUTTING THE RUBBER MAT OR CARPET. THIS WILL BE PERFORMED WITHOUT CHARGE.

Reported: 1977-03-22 (March 22, 1977) · Model years: 1977

THE WHEELS ON THE INVOLVED VEHICLES MAY BE EQUIPPED WITH AN IMPROPERLY FORMED SPIDER IN THE AREA WHERE THE SPIDER ATTACHES TO THE RIM. CONSEQUENTLY, THE CENTER SECTION OF THE WHEEL MAY DEVELOP CRACKS AND SEPARATE FROM THE WHEEL RIM.

Remedy: THE DEALER WILL REPLACE ALL DEFECTIVE WHEELS, FREE OF CHARGE.

Reported: 1978-08-07 (August 7, 1978) · Model years: 1978

THE FRONT NUTS MAY NOT HAVE BEEN TIGHTENED TO SPECIFICATIONS. THESE NUTS COULD LOOSEN DURING VEHICLE OPERATION AND CAUSE THE FRONT HUB AND ROTOR ASSEMBLY TO SEPARATE FROM THE WHEEL AND TIRE ASSEMBLY.

Remedy: THE DEALER WILL TIGHTEN THE NUTS TO SPECIFICATIONS ON ALL AFFECTED VEHICLES AT NO COST TO OWNER.

Reported: 1983-04-27 (April 27, 1983) · Model years: 1982

THE LOCKING SCREW THAT RETAINS THE PINION SHAFT IN PLACE IN THE DIFFERENTIAL COULD COME LOOSE. THE PINION SHAFT TURNS THE GEARS INSIDE THE DIFFERENTIAL THAT ROTATE THE DRIVE AXLES AND REAR WHEELS. IF THE LOCKING SCREW COMES LOOSE, IT COULD DAMAGE OTHER COMPONENTS OR JAM IN THE GEARS. IF THE PINION SHAFT COMES LOOSE, THE REAR WHEELS MAY NO LONGER POWER THE VEHICLE.

Remedy: THE DEALER WILL REPLACE THE DIFFERENTIAL LOCK SCREW AT NO CHARGE.

Reported: 1985-05-01 (May 1, 1985) · Model years: 1985

RIM INFORMATION MAY HAVE BEEN OMITTED ON CERTIFICATION LABEL INSTALLED ON THE LEFT FRONT DOOR. CONSEQUENCE OF DEFECT: THESE TRUCKS DO NOT CONFORM WITH FMVSS 120, TIRE SELECTIONS AND RIMS FOR VEHICLES OTHER THAN PASSENGER CARS.

Remedy: INSTALL NEW CORRECTED LABELS.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

CRUISE CONTROL CABLE LOCK MECHANISM MAY SELF DISENGAGE CAUSING ERRATIC OPERATION OR THROTTLE NOT RETURNING TO IDLE.

Consequence: ENGINE SPEED WOULD NOT DECREASE; LOSS OF ACCELERATORCONTROL COULD RESULT IN A CRASH WITHOUT PRIOR WARNING.

Remedy: INSTALL A CLAMP AROUND THE LOCK TAB OF CRUISE CONTROL.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

ONE OR BOTH OF OUTER TIE ROD NUTS MAY BE LOOSE AND NOT CRIMPED.

Consequence: LOSS OF ONE OR BOTH NUTS COULD LEAD TO TIE RODDISENGAGING FROM STEERING KNUCKLE RESULTING IN POSSIBLE LOSS OF STEERINGCONTROL AND POSSIBLY A CRASH.

Remedy: REPLACE TIE ROD AND KNUCKLE AND SET TOE-IN.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

TRUCKS MAY HAVE CRACKED OR BROKEN DOOR STRIKER NUTS, WHICH DO NOT CONFORM TO FMVSS 206.

Consequence: IN A COLLISION, CRACKED OR BROKEN STRIKER NUT COULDALLOW DOOR TO OPEN UNEXPECTEDLY AND POSSIBLY CAUSE INJURY TO OCCUPANTS.

Remedy: REPLACE EXISTING DOOR STRIKER NUTS.

Reported: 1987-08-10 (August 10, 1987) · Model years: 1988

INCORRECT FRONT SHOCK ABSORBER UPPER AND LOWER NUTS COULD LOOSEN.

Consequence: SHOCK ABSORBER COULD DETACH AND COME IN CONTACT WITHFRONT BRAKE HOSE; THIS CONTACT COULD RESULT IN A LEAK IN THE HOSE AND LOSS OFFRONT BRAKES.

Remedy: REPLACE FREE SPINNING NUTS WITH TORQUE NUTS.

Reported: 1989-07-06 (July 6, 1989) · Model years: 1988

TIRE SIZE DATA ON CERTIFICATION LABEL IS INCORRECT.

Consequence: INCORRECT TIRE INFORMATION FAILS TO CONFORM TOFMVSS 120.

Remedy: AFFIX NEW CERTIFICATION LABEL WITH CORRECT INFORMATION.

Reported: 1993-02-01 (February 1, 1993) · Model years: 1988, 1989, 1990, 1991, 1992, 1993

UNANTICIPATED HEAT IN THE TRANSMISSION CAN FORCE THE TRANSMISSION FLUID OUT OF THE VENT TUBE.

Consequence: THE VENTED TRANSMISSION FLUID CAN CATCH FIRE IF EXPOSEDTO A SOURCE OF IGNITION.

Remedy: INSTALL A LONGER TRANSMISSION VENT HOSE ROUTED TO THE LEFT SIDE OF THE ENGINE COMPARTMENT OF THE VEHICLE.

Reported: 1993-08-02 (August 2, 1993) · Model years: 1988, 1989, 1990, 1991, 1992

SEVERE CORROSION DUE TO ROAD SALT AT THE JOINT OF THE STAMPED STEEL CENTER SECTION AND THE CAST OUTER SECTION CAN CAUSE THE SECTIONS TO SEPARATE.

Consequence: SEPARATION OF THE ROTOR SECTIONS CAN CAUSE LOSS OFBRAKING ABILITY IN THE AFFECTED WHEEL. THIS COULD RESULT IN INCREASED STOPPINGDISTANCE AND/OR LOSS OF VEHICLE CONTROL AND AN ACCIDENT.

Remedy: REPLACE THE FRONT BRAKE ROTORS WITH NEW ROTORS WITH A CORROSION PROTECTION COATING. HOWEVER, IF REPLACEMENT OF BRAKE LININGS ARE NECESSARY, IT WILL BE DONE AT OWNER'S EXPENSE SINCE BRAKE LININGS ARE NORMAL MAINTENANCE ITEMS.

Reported: 1989-05-15 (May 15, 1989) · Model years: 1989

THERE MAY BE BELOW SPECIFIED TORQUE ON THE TRAILER HITCH ATTACHING FASTENERS, ALLOWING THE TRAILER HITCH TO MOVE UNDER TOWING LOADS.

Consequence: FASTENERS COULD FAIL; IF THIS OCCURS WHILE TRAILERIS BEING PULLED, HITCH AND TRAILER COULD SEPARATE AND A VEHICLE CRASH COULDOCCUR WITHOUT PRIOR WARNING.

Remedy: CORRECT TORQUE IN TRAILER HITCH FASTENERS TO PREVENT TRAILER SEPARATION.

Reported: 1990-01-29 (January 29, 1990) · Model years: 1990

ON C AND K MODELS, FEED AND OR RETURN FUEL LINES CAN CONTACT THE AUTOMATIC TRANSMISSION SHIFT LINKAGE CORDON SHAFT. IN ADDITION, ON K MODELS LINES MAY ALSO CONTACT FRONT PROPSHAFT. IN EITHER CASE THE FUEL LINES COULD BE DAMAGED RESULTING IN A FUEL LEAK.

Consequence: A HOLE COULD BE RUBBED THROUGH THESE FUEL LINES, ALLOWING FUEL LEAKAGE NEAR EXHAUST CROSSOVER PIPE; THIS COULD RESULT IN AN ENGINE COMPARTMENT FIRE THAT COULD SPREAD TO THE PASSENGER COMPARTMENT.

Remedy: INSTALL NEWLY DESIGNED FUEL LINE ROUTING BRACKET TO PREVENT CONTACT AND, IF NECESSARY, REPLACE FUEL LINES.

Reported: 1999-05-20 (May 20, 1999) · Model years: 1992

VEHICLE DESCRIPTION: EXTENDED-CAB PICKUP TRUCKS EQUIPPED WITH HIGH-BACK BUCKET SEATS. THE SEAT RECLINER TO FRAME ATTACHING BOLTS CAN LOOSEN, FATIGUE, AND FRACTURE ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION.

Reported: 1995-12-21 (December 21, 1995) · Model years: 1993, 1994

THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.

Consequence: IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

Reported: 1993-09-15 (September 15, 1993) · Model years: 1994

THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.

Consequence: BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.

Remedy: INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

Reported: 1993-12-14 (December 14, 1993) · Model years: 1994

THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."

Consequence: THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.

Remedy: DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

Reported: 1994-04-05 (April 5, 1994) · Model years: 1994

TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.

Consequence: IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.

Remedy: DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

Reported: 1994-10-26 (October 26, 1994) · Model years: 1994

THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.

Remedy: DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

Reported: 1996-04-04 (April 4, 1996) · Model years: 1995, 1996

THESE VEHICLES WERE ASSEMBLED WITH THE THROTTLE CABLE CONTACTING THE DASH MAT WHICH COULD BIND THE THROTTLE. THIS DOES NOT MEET WITH THE MAXIMUM RETURN TIMES REQUIRED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 124, "ACCELERATOR CONTROL SYSTEMS."

Consequence: CONSEQUENCE OF NON-COMPLIANCE: THE ENGINE SPEED MAY NOT RETURN TO IDLE INCREASING THE POTENTIAL FOR A VEHICLE ACCIDENT.

Remedy: DEALERS WILL INSPECT FOR ADEQUATE THROTTLE CABLE TO DASH MAT CLEARANCE, AND IF THERE IS INSUFFICIENT CLEARANCE, CUT OUT A PORTION OF THE DASH MAT TO PROVIDE PROPER CLEARANCE.

Reported: 1996-05-07 (May 7, 1996) · Model years: 1996

THE FOUR U-BOLTS NUTS ON EITHER SIDE OF THE REAR AXLE WERE UNDER-TORQUED.

Consequence: VEHICLE USAGE COULD CAUSE THE NUTS TO LOOSEN AND EVENTUALLY FALL OFF THE U-BOLT. THIS COULD RESULT IN SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE POTENTIAL FOR A VEHICLE CRASH.

Remedy: DEALERS WILL CHECK THE U-BOLT NUT TORQUE AND RE-TORQUE ANY LOOSE U-BOLTS TO SPECIFICATION.

Reported: 2000-08-08 (August 8, 2000) · Model years: 2000

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH VACUUM POWER, 4-WHEEL DISC BRAKES. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS." THESE VEHICLES WERE BUILT WITH A KINKED BRAKE BOOSTER VACUUM SUPPLY HOSE.

Consequence: THESE VEHICLES DO NOT COMPLY WITH REQUIREMENTS OF FMVSS NO. 105.

Remedy: DEALERS WILL RE-ROUTE THE BRAKE BOOSTER VACUUM SUPPLY HOSE.