Dodge D100 recalls by model year

Reported: 1966-10-12 (October 12, 1966) · Model years: 1964, 1965, 1966

Reported: 1968-03-20 (March 20, 1968) · Model years: 1968

Reported: 1969-02-13 (February 13, 1969) · Model years: 1969

Reported: 1969-04-09 (April 9, 1969) · Model years: 1969

Reported: 1971-11-10 (November 10, 1971) · Model years: 1972

Reported: 1972-07-25 (July 25, 1972) · Model years: 1972

Reported: 1972-12-01 (December 1, 1972) · Model years: 1973

Reported: 1972-12-01 (December 1, 1972) · Model years: 1973

Reported: 1977-11-28 (November 28, 1977) · Model years: 1977, 1978

THE FUEL TUBES (FUEL TANK TO PUMP) ON THE INVOLVED VEHICLES MAY BE ROUTED SUCH THAT TUBE TO UNDERBODY REINFORCEMENT FLANGE INTERFERENCE MAY RESULT DURING VEHICLE OPERATION. TUBE ABRASION CAUSED BY SUCH INTERFERENCE MAY RESULT IN FUEL LEAKAGE.

Remedy: DEALER WILL REROUTE THE FUEL TUBE OR INSTALL A NEW FUEL TUBE, IF DAMAGED, WITHOUT CHARGE TO OWNER.

Reported: 1978-02-17 (February 17, 1978) · Model years: 1977, 1978

Remedy: DEALER WILL INSPECT THE FUEL TANK VENT SYSTEMS FOR BLOCKAGE AND CORRECT, IF NECESSARY. FUEL TANKS WILL BE INSPECTED FOR CRACKING OF THE FRONT PANEL AND REPLACED, IF NECESSARY.

Reported: 1978-02-17 (February 17, 1978) · Model years: 1978

AN INTERMEDIATE STEERING SHAFT CONTAINING A MISMATCHED POT COUPLING ASSEMBLY MAY HAVE BEEN INSTALLED ON THE INVOLVED VEHICLES. THIS COUPLING MAY HAVE AN OVERSIZED SERRATION DIAMETER. AN OVERSIZED SERRATION COULD PREVENT THE COUPLING FROM ADEQUATELY TIGHTENING ONTO THE GEAR OR SHAFT SPLINES.

Remedy: THE DEALER WILL INSPECT AND, IF NECESSARY, INSTALL A REPLACEMENT SHAFT COUPLING.

Reported: 1978-06-14 (June 14, 1978) · Model years: 1978

IMPROPER ROUTING OF THE "HYDROBOOST" HYDRAULIC SYSTEM HIGH PRESSURE HOSE ASSEMBLY COULD ALLOW A TUBULAR SECTION TO CONTACT THE FRAME SIDE RAIL. ABRASION FROM THE CONTACT COULD RESULT, CAUSING A LEAK IN THE HOSE ASSEMBLY.

Remedy: THE DEALER WILL REROUTE "HYDROBOOST" HIGH PRESSURE HOSE ASSEMBLIES AND ANY DAMAGED HOSES WILL BE REPLACED.

Reported: 1978-08-29 (August 29, 1978) · Model years: 1978

DUE TO IMPROPER MATERIAL CONSTRUCTION THE HYDRO-BOOST FLUID RETURN HOSE MAY NOT BE CAPABLE OF WITHSTANDING THE TEMPERATURES AND/OR PRESSURES EXPERIENCED WITH THE HYDRO-BOOST SYSTEM. ALSO, THE HYDRO-BOOST FLUID HIGH PRESSURE HOSE ASSEMBLY MAY HAVE BEEN MISLOCATED, ALLOWING THE ASSEMBLY TO CONTACT THE FRAME SIDE RAIL. ABRASION RESULTING FROM CONTINUED CONTACT ALONG WITH IMPROPER MATERIAL CONSTRUCTION MAY CAUSE PRESSURE HOSE FAILURE. EITHER OF THESE CONDITIONS MAY CAUSE HYDRO-BOOST FLUID LEAKAGE, RESULTING IN THE LOSS OF POWER ASSIST FOR THE STEERING AND BRAKING SYSTEMS. COMPLETE LOSS OF STEERING OR BRAKING WILL NOT OCCUR SINCE BOTH SYSTEMS WOULD REVERT TO MANUAL OPERATION.

Remedy: THE DEALER WILL INSTALL A HYDRO-BOOST FLUID RETURN HOSE CONSTRUCTED FORM THE PROPER MATERIAL, POSITIONING THE HOSE ASSEMBLY TO ENSURE ADEQUATE CLEARANCE BETWEEN IT AND THE FRAME SIDE RAIL.

Reported: 1987-03-26 (March 26, 1987) · Model years: 1987

PLASTIC HYDRAULIC CLUTCH SYSTEM COMPONENTS ARE SUBJECT TO EXHAUST SYSTEM HEAT DAMAGE DUE TO PROLONGED COLD, HIGH SPEED IDLE OPERATION.

Consequence: CONSEQUENCE OF DEFECT: HYDRAULIC FLUID LEAKAGE COULD OCCUR CREATING THE POTENTIAL FOR A MINOR FIRE FROM FLUID CONTACTING THE HOT EXHAUST.

Remedy: INSTALL PROTECTIVE HEAT SHIELDS BETWEEN THE EXHAUST SYSTEM AND AFFECTED CLUTCH SYSTEM COMPONENTS.

Reported: 1990-07-06 (July 6, 1990) · Model years: 1987, 1988, 1989, 1990

IN A REAR END COLLISION, THE PICKUP BOX CROSSMEMBER COULD CONTACT THE FUEL PUMP MODULES FUEL LINE, CAUSING A FUEL LEAK WHICH WOULD BE IN NON-COMPLIANCE WITH FMVSS 301.

Consequence: CONSEQUENCE OF DEFECT: LEAKAGE OF FUEL COULD CAUSE A FIRE IF A SOURCE OF IGNITION IS PRESENT.

Remedy: INSTALL TWO PICKUP BOX REINFORCEMENT BLOCKER BRACKETS TO THE UNDERCARRIAGE TO ELIMINATE CONTACT WITH FUEL LINE.

Reported: 1987-12-26 (December 26, 1987) · Model years: 1988

AUTOMATIC TRANSMISSION MAY CONTAIN A PARK SPRAG ROD ASSEMBLY THAT MAY STICK IN THE TOOTH BUTT UNENGAGED POSITION.

Consequence: THIS CONDITION COULD ALLOW THE VEHICLE TO ROLL WITH THEGEAR SHIFT LEVER IN PARK POSITION.

Remedy: ALL INVOLVED VEHICLES WILL HAVE THE PARK SPRAG ROD ASSEMBLIES REPLACED.