Ford E150 recalls by model year

Reported: 1976-10-18 (October 18, 1976) · Model years: 1976

Reported: 1977-10-25 (October 25, 1977) · Model years: 1978

ON THE INVOLVED VEHICLES, THE PARK ACTUATION SUPPORT PLATES ARE DEFECTIVE DUE TO THEIR SUSCEPTIBILITY TO CRACKING DUE TO IMPROPER HEAT TREATMENT DURING MANUFACTURE. AS A RESULT, FRAGMENTS FROM A BROKEN PLATE CAN BECOME LODGED IN THE TRANSMISSION PARKING PAWL MECHANISM. THIS COULD PREVENT THE TRANSMISSION PARKING PAWL FROM ENGAGING WHEN THE SELECTOR LEVER IS PLACED IN THE "PARK" POSITION, OR PREVENT THE PAWL FROM BEING DISENGAGED FROM THE PARK GEAR.

Remedy: THE DEALER WILL REPLACE THE PARK ACTUATION CAM SUPPORT PLATES, FREE OF CHARGE, ON ALL AFFECTED VEHICLES.

Reported: 1977-11-15 (November 15, 1977) · Model years: 1978

ON THE INVOLVED VEHICLES, LEAKAGE MAY OCCUR AT THE THREADED CARBURETOR-TO-FUEL FILTER CONNECTION ON THE SUSPECT CARBURETORS. THIS IS DUE TO AN IMPROPERLY MACHINED CARBURETOR FUEL INLET CONNECTION.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, WILL REPLACE THE CARBURETOR WITHOUT CHARGE TO OWNER.

Reported: 1978-02-16 (February 16, 1978) · Model years: 1978

THE SHIFT SELECTOR REACTION SPRINGS MAY BE DEFORMED AS A RESULT OF IMPROPER INSTALLATION OF SELECTOR LEVERS DURING COLUMN BUILDUP. THUS THE LEVER MAY NOT BE ABLE TO BE MOVED INTO THE INSERT DETENTS LOCATED IN THE STEERING COLUMN ASSEMBLY. THIS COULD PREVENT THE "PARK" GEAR FROM BEING ENGAGED.

Remedy: DEALER WILL INSPECT AND, IF NECESSARY, REPLACE THE SHIFT SELECTOR REACTION SPRING WITHOUT CHARGE TO OWNER.

Reported: 1990-07-18 (July 18, 1990) · Model years: 1978, 1979, 1980, 1981, 1982, 1983, 1984

Consequence: OCCUPANTS WOULD NOT BE ADEQUATELY PROTECTED IN EVENT OFAN ACCIDENT OR SUDDEN STOP.

Remedy: INSTALL PROPER MOUNTING HARDWARE AND SEAT BELTS.

Reported: 1978-10-05 (October 5, 1978) · Model years: 1979

ON THE INVOLVED VEHICLES, THE POTENTIAL EXISTS FOR THE OUTBOARD SEAT BELTS TO BECOME TRAPPED IN THE SEAT-BED PIVOTING MECHANISM. SHOULD THE BELT BECOME TRAPPED IN THE MECHANISM WHEN THE SEAT IS CONVERTED TO A BED, THE BELT MAY BECOME CUT OR FRAYED.

Remedy: THE DEALER WILL INSTALL SEAT BELT SHIELDS ON THE FOLDING SEAT/BED PIVOTING MECHANISM AND REPLACE THE OUTBOARD SEAT BELT ASSEMBLIES IF DAMAGED, FREE OF CHARGE.

Reported: 1979-05-15 (May 15, 1979) · Model years: 1979

THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD.

Remedy: DEALER WILL REPLACE THE SUSPECT BRAKE RETAINING PIN.

Reported: 1979-06-19 (June 19, 1979) · Model years: 1979

CERTAIN VEHICLES MAY NOT CONTAIN THE SPECIFIED BODY MOUNTED HEAT SHIELDS. THIS COULD CAUSE HIGH FLOOR PAN TEMPERATURES WHEN THE ENGINE IS IDLED FOR EXTENDED PERIODS OF TIME. FOULED SPARK PLUGS OR OTHER ENGINE CONDITIONS COULD FURTHER INCREASE EXHAUST TEMPERATURES.

Remedy: THE DEALER WILL INSTALL THE NECESSARY FRAME MOUNTED HEAT SHIELD, IF MISSING.

Reported: 1979-08-07 (August 7, 1979) · Model years: 1979

THE WHEEL ASSEMBLY MAY CONTAIN SUBSTANDARD WELDS IN THE AREA WHERE THE DISC IS ATTACHED TO THE RIM. AS A RESULT, CRACKS CAN FORM IN THE WHEEL ASSEMBLY, CAUSING AIR LOSS AND AN UNDERINFLATED TIRE.

Remedy: DEALER WILL INSPECT AND REPLACE ANY DEFECTIVE WHEELS WITHOUT CHARGE TO OWNER.

Reported: 1980-07-14 (July 14, 1980) · Model years: 1980

DUE TO COMPUTER INPUT ERROR WHICH RESULTED IN AN INCORRECT BUILD SCHEDULE, SOME VEHICLES WERE SHIPPED WITHOUT THE REQUIRED EXHAUST SYSTEM HEAT SHIELDS. WHEN THE VEHICLE IS IDLED OVER AN EXTENDED PERIOD OF TIME, A MISSING EXHAUST HEAT SHIELD MAY RESULT IN DANGEROUSLY HIGH FLOOR PAN TEMPERATURES.

Remedy: DEALER WILL INSTALL FRAME-MOUNTING HEAT SHIELDS WITHOUT CHARGE TO OWNER.

Reported: 1980-09-19 (September 19, 1980) · Model years: 1980

CERTAIN VEHICLES WERE EQUIPPED WITH FRONT BRAKE HOSE ASSEMBLIES THAT WERE INCORRECTLY MANUFACTURED BY THE SUPPLIER. THESE ASSEMBLIES, BOTH RH AND LH, WERE INCORRECTLY BUILT WITH THE FITTINGS MISORIENTED BY 90 DEGREES. THIS COULD CAUSE CHAFING OF THE BRAKE HOSE THROUGH CONTACT WITH THE ADJACENT TIRE DURING FULL TURNS. CONTINUED CHAFING COULD RESULT IN A BRAKE FLUID LEAK.

Remedy: DEALER WILL INSPECT BOTH FRONT BRAKE HOSES AND, IF NECESSARY, REPLACE ONE OR BOTH HOSES AT NO CHARGE.

Reported: 1982-01-13 (January 13, 1982) · Model years: 1982

ON SOME OF THE INVOLVED VEHICLES, THE SHIFT ROD IN THE TRANSMISSION MAY NOT BE PROPERLY SEATED IN THE RETENTION GROMMET OF THE STEERING COLUMN SHIFT LEVER ASSEMBLY. IF THE SHIFT ROD WERE TO DISENGAGE, THE DRIVER COULD NOT SELECT THE PROPER TRANSMISSION FUNCTION WHICH WOULD CREATE THE POTENTIAL FOR UNEXPECTED MOVEMENT OF THE VEHICLE.

Remedy: DEALER WILL INSPECT THE SHIFT ROD ATTACHMENT AND MAKE SURE IT IS PROPERLY SEATED AT NO COST TO OWNER.

Reported: 1984-10-02 (October 2, 1984) · Model years: 1984

THE SECONDARY THROTTLE SHAFT MAY, WITH ACCUMULATED MILEAGE, BECOME CONTAMINATED AND MAY STICK IN A PARTIALLY OPEN POSITION WHILE DRIVING.

Consequence: CONSEQUENCE OF DEFECT: THIS STICKING COULD RESULT IN A FASTER SPEED THAN INTENDED, POSSIBLY RESUTLING IN AN ACCIDENT.

Remedy: THE PRIMARY TO SECONDARY THROTTLE CLOSURE LINK ON THE CARBURETOR WILL BE REPLACED FREE OF CHARGE.

Reported: 1990-06-01 (June 1, 1990) · Model years: 1989, 1990

UNDER CERTAIN CONDITIONS, THE SNAP RING THAT LOCATES THE PARK GEAR ON THE OUTPUT SHAFT OF THE TRANSMISSION MAY FRACTURE.

Consequence: WHEN THE GEAR IS PLACED IN PARK, THE PARK GEAR WOULD NOTENGAGE, ALLOWING THE TRUCK TO ROLL FREELY IF THE PARKING BRAKE IS NOT PROPERLYSET. THIS COULD RESULT IN AN ACCIDENT.

Remedy: INSTALL IMPROVED SNAP RING AND REVISED TRANSMISSION EXTENSION HOUSING.

Reported: 1991-09-04 (September 4, 1991) · Model years: 1989, 1990

THE DUAL FUEL TANK SELECTOR VALVE MAY MALFUNCTION AND CAUSE AN OVERFILL CONDITION IN ONE OF THE FUEL TANKS, RESULTING IN AN OVERFLOW OF FUEL PAST THE FILLER CAP.

Consequence: THE OVERFLOW OF FUEL PAST THE FILLER CAP CAUSES A FUELLEAKAGE, WHICH CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.

Remedy: REPLACE THE DUAL FUEL TANK SELECTOR VALVE.

Reported: 1991-07-03 (July 3, 1991) · Model years: 1990

SAFETY BELT ANCHORAGES DID NOT MEET LOAD REQUIREMENTS OF FMVSS 210; BELT ANCHORAGE BAR PULLED THROUGH THE FLOOR OF VEHICLE WHEN SUBJECTED TO LOADS OF FMVSS 210 TEST.

Consequence: SEAT OCCUPANTS WOULD NOT HAVE ADEQUATE PROTECTION IN THEEVENT OF A SUDDEN STOP OR ACCIDENT AND WOULD BE SUBJECT TO INCREASED RISKOF INJURY.

Remedy: SECURE SAFETY BELT ANCHORAGE BAR TO VEHICLE FRAME FOR ADDED STRENGTH.

Reported: 2004-11-26 (November 26, 2004) · Model years: 1997, 1998, 1999, 2000, 2004

ON CERTAIN VANS EQUIPPED WITH SURE-LOK WHEELCHAIR SECUREMENT SYSTEMS, THE SPROCKET TEETH OF THE RETRACTOR ASSEMBLY IS OUT OF ALIGNMENT.

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE WHEELCHAIR MAY NOT BE ADEQUATELY SECURED POSSIBLY RESULTING IN INJURIES TO A WHEELCHAIR OCCUPANT.

Remedy: DEALERS WILL INSPECT AND REPLACE THE WHEELCHAIR SECUREMENT RETRACTORS AS NECESSARY. SURE-LOK WILL HANDLE THE REPAIRS FOR THIS CAMPAIGN. OWNERS SHOULD CONTACT SURE-LOCK AT 1-908-231-1804 OR MOBILITYWORKS AT 1-800-769-8267.

Reported: 2014-10-10 (October 10, 2014) · Model years: 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013

Mobility Works (WMK Inc.) is recalling certain model year 2006-2014 Ford E150, E250, and E350 vans modified by Mobility Works to be equipped with certain model S2005, S2010, S5005, S5010, S5505, and S5510 wheelchair lifts manufactured by Ricon Corporation. The platform side plate of the affected wheelchair lifts may crack.

Consequence: If the platform side plates crack, the lift platform can separate from the lift and come to rest against the vehicle's lift door. When the doors are opened, the platform may fall out, increasing the risk of injury to the lift operator.

Remedy: Mobility Works will notify owners, and Ricon will supply supplemental platform support bumpers. Any platform that has already started cracking will be replaced, free of charge. The recall began on November 10, 2014. Owners may contact Mobility Works customer service at 1-800-769-8267 or Ricon customer service at 1-800-322-2884.