Winnebago TOUR recalls by model year

Reported: 2008-05-19 (May 19, 2008) · Model years: 2005, 2006, 2007, 2008, 2009

WINNEBAGO IS RECALLING 1,699 MY 2005-2009 WINNEBAGO JOURNEY, TOUR AND ITASCA MERIDIAN AND ELLIPSE MOTOR HOMES BUILT ON THE FREIGHTLINER XC CHASSIS. THE CHASSIS CONTAINS STEERING FILTERS THAT CAN PLUG DUE TO FAILURE OF THE SCREEN ADHESION TO THE FILTER HOUSING CAUSING A RISE IN RETURN LINE PRESSURE POTENTIALLY LEADING TO A HOSE SEPARATION FROM THE FILTER OR STEERING GEAR FITTING RESULTING IN A SUDDEN LOSS OF STEERING FLUID AND POWER ASSIST.

Consequence: SUDDEN LOSS OF STEERING ASSIST WITHOUT WARNING INVOLVING A MOTOR HOME COULD BE A PROBLEM FOR CERTAIN DRIVERS INCREASING THE RISK OF A CRASH.

Remedy: FREIGHTLINER IS CONDUCTING THIS RECALL AND WILL REPLACE THE AFFECTED FILTERS WITH A LARGER FILTER (PLEASE SEE 07V570). OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712 OR WINNEBAGO AT 1-641-585-3535.

Reported: 2005-11-01 (November 1, 2005) · Model years: 2006

ON CERTAIN MOTOR HOMES, THE CINCH BOLT, WHERE THE STEERING COLUMN CONNECTS TO THE INTERMEDIATE SHAFT, WAS IMPROPERLY TIGHTENED. THIS COULD RESULT IN THE BOLT THREADS BEING STRIPPED, CONCEIVABLY NOT PROVIDING A TIGHT JOINT.

Consequence: IF THE JOINT IS LOOSE, THE INTERMEDIATE SHAFT HAS THE POTENTIAL TO SLIP OFF THE SPLINE SHAFT OF THE STEERING COLUMN CAUSING LOSS OF STEERING CONTROL. THIS COULD RESULT IN PERSONAL INJURY OR VEHICLE AND PROPERTY DAMAGE.

Remedy: DEALERS WILL INSPECT AND REPLACE THE CINCH BOLT AND NUT. THE RECALL BEGAN NOVEMBER 4, 2005. OWNERS MAY CONTACT WINNEBAGO AT 641-585-6939.

Reported: 2005-12-28 (December 28, 2005) · Model years: 2006

ON CERTAIN MOTOR HOMES EQUIPPED WITH KWIKEE BRAND ELECTRIC STEPS, THE STEPS MAY HAVE BEEN MANUFACTURED WITH DEFECTIVE STEP CONTROL UNITS.

Consequence: THE DEFECTIVE CONTROL UNITS COULD DEVELOP AN ELECTRICAL SHORT ALLOWING FOR THE POTENTIAL OF THE PLASTIC CASE TO IGNITE, POSSIBLY RESULTING IN PERSONAL INJURY AND/OR VEHICLE AND PROPERTY DAMAGE.

Remedy: DEALERS WILL INSPECT THE KWIKEE STEP AND REPLACE THE STEP CONTROL UNIT, IF NECESSARY, FREE OF CHARGE. THE RECALL BEGAN ON DECEMBER 23, 2005. OWNERS MAY CONTACT WINNEBAGO AT 1-800-537-1885.

Reported: 2007-08-29 (August 29, 2007) · Model years: 2006, 2007

ON CERTAIN MOTOR HOMES BUILT WITH CUMMINS ISL CM850 DIESEL ENGINES, THE CONNECTING ROD CONTAINS A MACHINING DEFECT IN THE WRIST PIN BUSHING OF THE ROD THAT COULD CAUSE A SEIZURE OF THE PISTON PIN.

Consequence: IF ALLOWED TO PROGRESS, THIS CAN LEAD TO ENGINE FAILURE WITH THE POSSIBILITY OF THE ROD RUPTURING THE LOCK CAVITY, SPILLING OIL AND DEBRIS ONTO THE ROADWAY INCREASING THE RISK OF A CRASH.

Remedy: WINNEBAGO IS WORKING WITH CUMMINS TO RECALIBRATE THE ENGINE CONTROL MODULE AND ENHANCE THE ENGINE PROTECTION SYSTEM ENABLING IT TO PROVIDE EARLY DETECTION OF THE FAILURE MODE AND AVOID MORE SERIOUS ENGINE DAMAGE AND RESULTANT SAFETY HAZARD. CUMMINS WILL ALSO INSTALL A NEW VALVE COVER WITH A CRANKCASE PRESSURE SENSOR FREE OF CHARGE (PLEASE SEE 07E033). OWNERS MAY CONTACT CUMMINS AT 1-800-343-7357 OR WINNEBAGO AT 641-585-3535.

Reported: 2008-08-12 (August 12, 2008) · Model years: 2006, 2007, 2008

WINNEBAGO IS RECALLING 31 MY 2006-2008 ITASCA CAMBRIA, HORIZON, WINNEBAGO ACCESS, ADVENTURER, JOURNEY, MINNIE WINNIE, SIGNTSEER, TOUR, VECTRA, AND VOYAGE MOTOR HOMES EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE LIFTS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 403, "PLATFORM LIFT SYSTEMS FOR MOTOR VEHICLES." THE ANTI-STOW INTERLOCK MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER. THE PRESSURE SENSING SWITCH THAT DETECTS THE PRESENCE OF WEIGHT ON THE PLATFORM WAS NOT ADJUSTED TO THE NECESSARY SENSITIVITY LEVEL. THE LIFT COULD STOW EVEN THOUGH SOMEONE OR SOMETHING IS STILL ON THE LIFT.

Consequence: A LIFT OCCUPANT CAN BE INJURED SHOULD THE LIFT BEGIN TO STOW UNINTENTIONALLY.

Remedy: WINNEBAGO IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS (PLEASE SEE 07E097). OWNERS MAY CONTACT RICON AT 1-800-322-2884 OR WINNEBAGO AT 1-641-585-3535.

Reported: 2008-03-28 (March 28, 2008) · Model years: 2007

WINNEBAGO IS RECALLING 31 MY 2006-2008 JOURNEY, VOYAGE, MY 2006-2007 SIGHTSEER, MY 2006 ADVENTURER, MINNIE WINNIE, MY 2007 ACCESS, TOUR, VECTRA, ITASCA CAMBRIA, AND MY 2007-2008 ITASCA HORIZON MOTOR HOMES EQUIPPED WITH RICON PLATFORM STYLE WHEELCHAIR LIFTS. THESE MOTOR HOMES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 404, "PLATFORM LIFT INSTALLATIONS IN MOTOR VEHICLES." THE THRESHOLD WARNING SYSTEM MAY NOT DETECT THE PRESENCE OF A WHEELCHAIR OR MOBILITY AID USER IN A CERTAIN SPOT WITHIN THE DEFINED THRESHOLD AREA.

Consequence: THE USER OF THE LIFT COULD BE INJURED SHOULD THE LIFT MOVE UNINTENTIONALLY.

Remedy: WINNEBAGO IS WORKING WITH RICON TO CORRECT THE WHEELCHAIR LIFTS FREE OF CHARGE (PLEASE SEE 07E095). THE RECALL BEGAN ON APRIL 9, 2008. OWNERS MAY CONTACT RICON AT 1-818-267-3000.

Reported: 2008-05-19 (May 19, 2008) · Model years: 2007, 2008

WINNEBAGO IS RECALLING 306 MY 2007-2008 JOURNEY, DESTINATION, TOUR AND ITASCA MERIDIAN, LATITUDE, AND ELLIPSE MOTOR HOMES BUILT ON FREIGHTLINER CHASSIS. THE FASTENERS THAT ATTACH THE STEERING ARM OR TIE ROD ARMS TO THE SPINDLE MAY BE OVER OR UNDER-TIGHTENED.

Consequence: INCORRECTLY TIGHTENED STEERING ARM FASTENERS MAY FATIGUE AND FRACTURE WHICH COULD CAUSE A CRASH WITHOUT WARNING.

Remedy: WINNEBAGO IS WORKING WITH FREIGHTLINER TO REPAIR THESE VEHICLES FREE OF CHARGE (PLEASE SEE 07V306). OWNERS MAY CONTACT FREIGHTLINER AT 1-800-547-0712 OR WINNEBAGO AT 1-641-585-3535.

Reported: 2008-10-30 (October 30, 2008) · Model years: 2008, 2009

WINNEBAGO IS RECALLING 594 MY 2008-2009 DESTINATION, JOURNEY, TOUR, VECTRA, AND ITASCA LATITUDE, MERIDIAN, ELLIPSE, AND HORIZON MOTOR HOMES EQUIPPED WITH SAF-HOLLAND ADL SERIES REAR SUSPENSIONS. IN SOME INSTANCES THE TRANSVERSE BEAM WAS NOT PROPERLY WELDED WHICH COULD RESULT IN A FAILURE OF THE WELD.

Consequence: IF THE WELD FAILS, VEHICLE STABILITY WHILE CORNERING COULD BE AFFECTED RESULTING IN LOSS OF VEHICLE CONTROL, POSSIBLY RESULTING IN A CRASH. IN ADDITION, THE TRANSVERSE BEAM COULD DROP TO THE GROUND CAUSING SPARKS THAT COULD CAUSE A FIRE HAZARD.

Remedy: WINNEBAGO IS WORKING WITH DAIMLER TRUCKS/SAF-HOLLAND TO HAVE A VISUAL INSPECTION OF THE ADL TRANSVERSE BEAM PERFORMED. IF A WELD DEFECT IS IDENTIFIED, SAF-HOLLAND WILL PROVIDE A SERVICE REPLACEMENT KIT THAT CONTAINS A NEW TRANSVERSE BEAM, ALL NECESSARY INSTALLATION HARDWARE, BEAM REPLACEMENT, AND INSTRUCTIONS FREE OF CHARGE (PLEASE SEE 08V269 AND 08E031). OWNERS MAY CONTACT DAIMLER TRUCKS AT 1-800-547-0712, SAF-HOLLAND AT 1-231-773-3271, OR WINNEBAGO AT 1-641-585-3535.

Reported: 2010-03-25 (March 25, 2010) · Model years: 2008, 2009

WINNEBAGO HAS NOTIFIED NHTSA OF A DEFECT IN CERTAIN MODEL YEAR 2008-2009 MOTORHOMES FITTED WITH RICON PUBLIC USE LIFTS. THE RESTRAINT BELT ON THESE LIFTS WAS DESIGNED TO PREVENT THE LIFT FROM MOVING, UNLESS THE TONGUE OF THE BELT IS FULLY ENGAGED AND LATCHED IN THE BUCKLE. RICON HAS DISCOVERED, HOWEVER, THAT IT IS POSSIBLE FOR THE OPERATOR TO INSERT THE BELT TONGUE INTO THE BUCKLE WITHOUT FULLY ENGAGING THE LATCHING MECHANISM. IN THIS CASE, THE RESTRAINT BELT WOULD APPEAR TO BE LATCHED, AND THE OPERATOR COULD RUN THE LIFT. IF THE RESTRAINT BELT TONGUE IS NOT FULLY ENGAGED INTO THE RESTRAINT BELT BUCKLE, AND LATCHED, THE LIFT MAY OPERATE WITH AN OCCUPANT ON THE PLATFORM.

Consequence: THE USER OF THE LIFT COULD BE INJURED SHOULD THE LIFT MOVE WITHOUT THE RESTRAINT BELT PROPERLY BUCKLED.

Remedy: WINNEBAGO IS WORKING WITH RICON AND RICON WILL BE HANDLING THE REMEDY FOR THIS CAMPAIGN. PLEASE SEE RICON'S DEFECT REPORT 09E-060. RICON WILL PROVIDE CUSTOMERS WITH A WARNING DECAL AND A DVD-BASED TRAINING AID. THE SAFETY RECALL BEGAN ON JULY 6, 2010. OWNERS MAY CONTACT RICON CUSTOMER SERVICE AT 1-800-322-2884 OR BY EMAIL AT [email protected].

Reported: 2011-02-14 (February 14, 2011) · Model years: 2010, 2011

WINNEBAGO IS RECALLING CERTAIN MODEL YEAR 2010-2011 TOUR AND ITASCA ELLIPSE MOTOR HOMES MANUFACTURED FROM AUGUST 7, 2009 THROUGH FEBRUARY 7, 2011, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF PART 567, "CERTIFICATION." THE VEHICLES ARE EQUIPPED WITH LABELS INDICATING THE WRONG TYPE OF LOAD RANGE TIRES.

Consequence: THESE VEHICLES DO NOT COMPLY WITH THE REQUIREMENTS OF PART 567 CERTIFICATION.

Remedy: OWNERS WILL BE PROVIDED WITH NEW TIRE INFORMATION LABELS AND INSTALLATION INSTRUCTIONS. AT THE CUSTOMER'S OPTION, A DEALER CAN PERFORM THE INSTALLATION FOR THEM. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON FEBRUARY 25, 2011. OWNER MAY CONTACT WINNEBAGO AT 1-641-585-6939.

Reported: 2012-12-06 (December 6, 2012) · Model years: 2010, 2011, 2012, 2013

Winnebago Industries is recalling certain model year 2010-2013 Winnebago Journey and Tour motorhomes, and certain model year 2010-2013 Itasca Meridian and Ellipse motorhomes, manufactured June 18, 2010, through November 17, 2011. The chassis are equipped with connectors for diode jumpers that may come loose, resulting in an open circuit. Two circuits are affected: The one that disengages the cruise control with brake pedal use, and the one that illuminates the brake lights with brake pedal use.

Consequence: Failure of the cruise control to disengage when the brakes are applied may increase the risk of a vehicle crash. Without the brake lights illuminating when the brakes are applied, the driver's intent is not communicated, increasing the risk of a crash.

Remedy: Daimler Trucks North America will be conducting the recall on behalf of Winnebago Industries. Daimler will notify owners, and dealers will inspect the the diode jumpers to make sure they are fully locked in place and will correct the vehicles as needed. The recall began December 26, 2012. Owners should contact Winnebago at 1-641-585-3535 or Daimler Trucks at 1-503-745-6910.

Reported: 2011-03-08 (March 8, 2011) · Model years: 2011

WINNEBAGO IS RECALLING CERTAIN MODEL YEAR 2011 TOUR AND ITASCA ELLIPSE MOTOR HOMES MANUFACTURED FROM AUGUST 9, 2010 THROUGH JANUARY 21, 2011. THESE VEHICLES HAVE THE POTENTIAL FOR A LP HOSE CONNECTION TO BE DAMAGED WHEN THE SLIDEOUT ROOM IS OPERATED. IF THE LP HOSE MAKES CONTACT WITH THE SLIDEOUT RAM, IT COULD BE DISCONNECTED. IF THIS WERE TO HAPPEN, A LEAK WOULD OCCUR WHEN THE LP TANK IS OPENED.

Consequence: THE LEAKING LP THEN HAS THE POTENTIAL TO IGNITE, WHICH COULD RESULT IN PERSONAL INJURY OR DEATH.

Remedy: DEALERS WILL INSPECT THE HOSE AND RELOCATE A PIPE CLAMP AS WELL AS ADDING A SECOND CLAMP TO THE HOSE TO ENSURE CLEARANCE IS MAINTAINED DURING THE OPERATION OF THE SLIDEROOM. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 25, 2011. OWNER MAY CONTACT WINNEBAGO AT 641-585-6939.

Reported: 2011-10-20 (October 20, 2011) · Model years: 2011

WINNEBAGO IS RECALLING CERTAIN MODEL YEAR 2011 JOURNEY, MERIDIAN, TOUR, ELLIPSE MOTOR HOMES AND WINNEBAGO COMMERCIAL VEHICLES BUILT ON MC, XCL, AND XCS CHASSIS FROM SEPTEMBER 1, 2010, THROUGH DECEMBER 31, 2010, AND EQUIPPED WITH A CUMMINS ISX OR ISL DIESEL ENGINE. THE V-BAND CLAMP ASSEMBLY, PART NUMBERS Q187684, Q187685, AND Q187686, USED TO CONNECT THE INLET AND OUTLET CONE SECTIONS TO THE DIESEL OXIDATION CATALYST (DOC)/DIESEL PARTICULATE FILTER (DPF) INCLUDE A T-BOLT WHICH CAN FRACTURE AND FAIL WHEN SUBJECTED TO STRESS OR LOAD. A FRACTURE OR FAILURE OF THE T-BOLT MAY CAUSE THE CLAMP TO LOOSEN AND THE INLET OR OUTLET SECTIONS ATTACHED TO THE DOC/DPF HOUSING TO DISCONNECT.

Consequence: IF THE INLET OR OUTLET SECTIONS DISCONNECT, HOT EXHAUST GASES CAN VENT PRIOR TO EXITING THE TAILPIPE, CREATING THE RISK OF COMBUSTION AND A FIRE. IF BOTH CLAMPS FAIL, THERE IS A RISK IN SOME APPLICATIONS THAT THE DOC/DPF HOUSING MAY DETACH COMPLETELY, CREATING A ROAD HAZARD.

Remedy: WINNEBAGO IS WORKING WITH DAIMLER TRUCKS NORTH AMERICA (THE SUPPLIER OF THE CHASSIS) AND CUMMINS TO IDENTIFY AND NOTIFY OWNERS OF THE RECALL CAMPAIGN. THE MANUFACTURER HAS NOT YET PROVIDED THE AGENCY WITH A REMEDY PLAN FOR THIS CAMPAIGN. THE SAFETY RECALL BEGAN OCTOBER 10, 2011. OWNERS MAY CONTACT CUMMINS AT 1-812-377-5000.

Reported: 2015-10-06 (October 6, 2015) · Model years: 2013, 2014, 2015, 2016

Winnebago Industries, Inc. (Winnebago) is recalling certain model year 2013-2016 Winnebago Era, Travato, View, Trend, Via, Journey, and Tour motorhomes and Itasca Navion, Viva, Reyo, Meridian, and Elipse motorhomes manufactured June 26, 2012, to August 26, 2015. In the affected vehicles, the high pressure liquid propane (LP) hose may harden and result in an LP leak at the crimp fitting.

Consequence: An LP leak in the presence of an ignition source increases the risk of a fire.

Remedy: Winnebago will notify owners, and dealers will replace the LP hose, free of charge. The recall began on November 25, 2015. Owners may contact Winnebago customer service at 1-641-585-3535.

Reported: 2017-12-07 (December 7, 2017) · Model years: 2013, 2014, 2015, 2016, 2017, 2018

Winnebago Industries, Inc. (Winnebago) is recalling certain 2013-2018 Winnebago Era, Travato, Minnie Winnie, Fuse, View, Trend, Aspect, Brave, Vista, Sightseer, Adventurer, Forza, Journey, Tour, Revel, Paseo, Chalet, Access, and Intent motorhomes and Commercial vehicles, and 2013-2018 Itasca Spirit, Navion, Cambria, Tribute, Sunstar, Sunova, Suncruiser, Solei, Meridian, Elipse, Horizon, Reyo, and Via motorhomes. These vehicles are equipped with Kidde Plastic-Handle or Push Button 'Pindicator' fire extinguishers that may become clogged, preventing the extinguisher from discharging as expected or excessive force may be needed to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

Remedy: Winnebago will notify owners, instructing them to contact Kidde for replacement or aftermarket fire extinguishers, free of charge. The recall began on January 19, 2018. Owners may contact Winnebago customer service at 1-641-585-3535, or Kidde customer service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information.

Reported: 2024-10-01 (October 1, 2024) · Model years: 2013, 2014, 2015, 2016, 2017

Winnebago Industries, Inc. (Winnebago) is recalling certain 2013-2017 Tour, 2013-2018 Journey, 2014-2022 Forza, 2015-2016 Brave, 2015-2019 Grand Tour, 2015-2021 Vista, 2016-2018 Adventurer, Sightseer, 2016-2021 Commercial Vehicle, 2018-2021 Intent, Sunstar, 2018-2020 Horizon, Itasca 2013-2017 Ellipse, Meridian, 2014-2017 Solei, 2015-2016 Tribute, 2015-2018 Sunstar, 2016-2018 Suncruiser, and Sunova motorhomes. The turn signals may have a smaller than required luminous lens area. As such these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 108, "Lamps, Reflective Devices, and Associated Equipment."

Consequence: A small lens can make it difficult for other drivers to see the turn signal, increasing the risk of a crash.

Remedy: Dealers will replace the turn signals, free of charge. Owner notification letters were mailed April 17, 2026. Owners may contact Winnebago Customer Care at 1-800-537-1885. Winnebago's number for this recall is 189.

Reported: 2016-04-25 (April 25, 2016) · Model years: 2014

Winnebago Industries, Inc (Winnebago) is recalling certain model year 2014 Winnebago Tour, and Itasca Ellipse vehicles manufactured May 23, 2013, to August 9, 2013 and built on a Freightliner chassis. On certain recreational vehicles built with a heavier, adjustable foot pedal, the brake activation signal to certain towed devices may not deactivate when the service brakes are released.

Consequence: If the brake activation signal to a towed device remains active when the motorhome chassis service brakes are released, the brakes on a towed device may remain engaged depending on brake configuration of the trailer. As a result, the brakes would drag and possibly overheat potentially resulting in a fire. Additionally, following drivers may be confused by the motorhome's actions, increasing the risk of a crash.

Remedy: Daimler Trucks North America, LLC., (DTNA) will notify owners, and dealers will modify the affected brake assemblies, free of charge. The recall began on June 6, 2016. Owners may contact Daimler Truck North America, LLC., customer service at 1-800-745-8000. DTNA's Recall number for this recall campaign is FL-704. Owners may also contact Winnebago customer service at 1-641-585-3535.

Reported: 2016-06-22 (June 22, 2016) · Model years: 2014, 2015, 2016

Winnebago Industries, Inc. (Winnebago) is recalling certain model year 2014-2016 Winnebago Tour motorhomes manufactured May 25, 2013, to November 25, 2015, and Itasca Ellipse motorhomes manufactured May 25, 2013, to November 18, 2015. The throttle pedal position sensor on the affected vehicles may not return to zero, causing the engine brake to suddenly not activate as expected, reducing the vehicle's deceleration ability.

Consequence: A sudden loss of an engine brake without warning on a motorhome may lead to a reduced brake ability, potentially increasing the risk of a crash.

Remedy: Daimler Trucks North America has notified owners, and dealers, will replace the throttle pedal, free of charge. An interim notification was distributed to owners on July 8, 2016. The recall began on August 15, 2016. Owners may contact Daimler Warranty Campaign Department at 1-800-547-0712 or email [email protected].

Reported: 2016-05-31 (May 31, 2016) · Model years: 2015, 2016

Winnebago Industries, Inc (Winnebago) is recalling certain model year 2015-2016 Winnebago Tour and Itasca Ellipse motor homes manufactured August 29, 2014, to November 4, 2015 and built on a Freightliner chassis. In the affected vehicles, the steering box may have been manufactured with an incorrect spacer with insufficient height that can cause too much play, causing the connection to wear between the steering wheel and the front axle.

Consequence: The steering wheel's connection to the front axle could fail resulting in a sudden loss of steering ability, increasing the risk of a crash.

Remedy: Daimler Trucks of North America will notify owners, and Freightliner dealers will inspect and replace the steering gears, as necessary, free of charge. The recall began on May 31, 2016. Note: Owners are urged not to drive their vehicles until they have been inspected. Owners may contact Freightliner at 1-800-547-0712.

Reported: 2018-08-17 (August 17, 2018) · Model years: 2016, 2017, 2018, 2019

Winnebago Industries, Inc (Winnebago) is recalling certain 2016-2019 Winnebago Era, Travato, Fuse, View, Trend, Aspect, Paseo, Via, Adventurer, Journey, Tour, and Grand Tour motorhomes. These vehicles have an auxiliary solar charging port circuit that is not fused.

Consequence: If solar panels are connected and they exceed the amperage capacity of the circuit, the unprotected circuit can increase the risk of a fire.

Remedy: Winnebago will notify owners, and dealers will install an inline 15 amp fuse into the auxiliary solar charging port circuit, free of charge. Winnebago issued interim notifications to owners on December 4, 2018. The recall began June 5, 2019. Owners may contact Winnebago customer service 1-641-585-6939 or 1-800-537-1885.