Ford RANGER recalls by model year

Reported: 1982-04-12 (April 12, 1982) · Model years: 1983

ON THE INVOLVED VEHICLES, THE MUFFLER GRASS SHIELDS WERE INADVERTENTLY OMITTED DURING MANUFACTURE. WITHOUT THE GRASS SHIELD, AND DURING CERTAIN OPERATING CONDITIONS, THE MUFFLER SURFACE TEMPERATURES COULD BECOME HOT ENOUGH TO EXCEED SPECIFIED STANDARDS AND CREATE THE POTENTIAL FOR IGNITING TALL GRASSES IF THEY WERE PRESENT BENEATH A STANDING VEHICLE.

Remedy: DEALER WILL INSTALL GRASS SHIELDS ON ALL AFFECTED VEHICLES AT NO COST TO OWNER.

Reported: 1983-03-22 (March 22, 1983) · Model years: 1983

SOME OF THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY HEAT TREATED FRONT SUSPENSION LOWER SPRING SEAT ATTACHING STUDS. THESE STUDS COULD FRACTURE DURING VEHICLE OPERATION, ALLOWING THE LOWER SPRING SEAT TO MOVE AND POSSIBLY SLIDE OFF THE AXLE.

Remedy: THE DEALER WILL REPLACE THE LOWER SPRING SEAT STUDS ON BOTH THE LEFT AND RIGHT SIDES OF THE VEHICLE AT NO CHARGE TO OWNERS.

Reported: 1984-07-09 (July 9, 1984) · Model years: 1983, 1984

IF TRUCK IS STRUCK FROM THE SIDE, THE CAP ON THE FUEL TANK COULD BECOME UNSEALED, ALLOWING UNSAFE LEAKAGE OF FUEL. THIS IS A FAILURE TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 301, "FUEL SYSTEM INTEGRITY". LEAKAGE CAN BE CAUSED BY AN ORANGE-COLORED PLASTIC DIESEL FUEL INFORMATION RING WHICH IS FOUND AROUND THE FUEL TANK NECK, OR BY THE TETHER.

Remedy: UPON INSPECTION, FUEL CAP TETHERS WILL BE REPLACED OR DIESEL FUEL INFORMATION RINGS WILL BE REMOVED.

Reported: 1984-09-25 (September 25, 1984) · Model years: 1983, 1984

SECONDARY HOOD LATCH COMPONENTS MAY HAVE BEEN IMPROPERLY POSITIONED DURING ASSEMBLY. IF THE HOOD IS NOT CLOSED TIGHTLY, OR IS INADVERTENTLY RELEASED, THE SECONDARY LATCH MAY NOT WORK AND THE HOOD MAY FLY UP WITHOUT PRIOR WARNING.

Remedy: THE HOOD ASSEMBLY WILL BE INSPECTED AND THE HOOD AND LATCH COMPONENTS WILL BE ADJUSTED, IF NECESSARY, WITHOUT CHARGE TO THE OWNER.

Reported: 1984-09-25 (September 25, 1984) · Model years: 1983

THE FLEXIBLE HOSE CONNECTING THE FUEL PUMP TO THE CARBURETOR FUEL LINE MAY SEPARATE FROM THE FUEL PUMP.

Remedy: THE EXISTING FUEL HOSE WILL BE REPLACED AND TWO NEW HOSE CLAMPS WILL BE INSTALLED.

Reported: 1983-11-07 (November 7, 1983) · Model years: 1984

VEHICLES MAY HAVE FUEL OR VAPOR LINE DAMAGE CAUSED WHEN AN INCORRECT PROCEDURE WAS USED IN TIGHTENING BOLTS ON ADJACENT COMPONENTS DURING ASSEMBLY. THE FUEL TANK MAY BECOME DAMAGED DUE TO A LOOSE CROSS MEMBER THAT SUPPORTS IT.

Remedy: VEHICLES WILL BE INSPECTED AND, WHEN NECESSARY, FUEL AND VAPOR LINES WILL BE REPLACED AND THE CROSS MEMBER WILL BE TIGHTENED.

Reported: 1983-12-20 (December 20, 1983) · Model years: 1984

THE BOLTS THAT ATTACH THE D-SHAPED RING FOR THE SHOULDER BELT ARE INADEQUATELY SUPPORTED BY THE MATERIAL IN WHICH THEY ARE MOUNTED. THE ATTACHMENT DOES NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES".

Remedy: DEALERS WILL INSTALL NEW ATTACHING HARDWARE TO IMPROVE THE STRENGTH OF THE MOUNTING.

Reported: 1984-03-06 (March 6, 1984) · Model years: 1984

COMPONENTS IN THE LOCKING HUBS WERE IMPROPERLY HEAT-TREATED AND MAY CRACK OR FRACTURE UPON ENGAGEMENT OF THE FRONT DRIVE AXLES. THE BROKEN COMPONENT ON THE LEFT FRONT WHEEL MAY BECOME JAMMED AGAINST THE NUT.

Remedy: CAM ASSEMBLIES IN FRONT WHEEL AUTOMATIC LOCKING HUBS WILL BE REPLACED.

Reported: 1984-09-06 (September 6, 1984) · Model years: 1984

WEIGHT RATING INFORMATION IS INCORRECT ON VEHICLE MANUAL LABELS AND RATING DECALS.

Remedy: DEALERS WILL BE PROVIDED WITH THE REVISED VEHICLE INFORMATION. IF VEHICLE WEIGHT IS FOUND TO BE GREATER THAN THAT SPECIFIED ON WEIGHT RATING, THE AFFECTED VEHICLE"S REAR AXLE MAY BE REPURCHASED FROM FORD. A PRICE ADJUSTMENT WILL ALSO BE MADE IF APPROPRIATE.

Reported: 1985-04-17 (April 17, 1985) · Model years: 1985

THE NYLON FUEL SUPPLY AND RETURN LINES ARE IMPROPERLY ROUTED ALONG THE FRAME SIDE RAIL AND COULD CONTACT THE UNIVERSAL JOINT ON THE FRONT DRIVESHAFT. CONSEQUENCE OF DEFECT: SUCH CONTACT COULD CAUSE ABRASION OF THE LINES AND LOW PRESSURE FUEL LEAKAGE CREATING THE POTENTIAL FOR A FIRE.

Remedy: REROUTE OR REPLACE AFFECTED FUEL LINES.

Reported: 1985-09-24 (September 24, 1985) · Model years: 1986

THE ELECTRONIC ENGINE CONTROL WIRING HARNESS INSULATION MAY BE DAMAGED DUE TO COPPER SPIKES PRODUCED DURING THE WELDING OF ITS WIRES. THIS CREATES A POTENTIAL FOR A SHORT CIRCUIT BETWEEN THE WIRES WHICH ENERGIZE THE FUEL PUMP, CAUSING SOME FUEL INJECTORS TO OPEN, DISCHARGING FUEL INTO THE ENGINE. CONSEQUENCE OF DEFECT: FUEL DISCHARGED INTO THE ENGINE WOULD EVENTUALLY LEAK THROUGH THE EXHAUST SYSTEM TO THE GROUND. THIS COULD RESULT IN A FIRE IF A SOURCE OF IGNITION IS PRESENT.

Remedy: REPAIR WIRING HARNESS, CHECK ENGINE AND CATALYST FOR DAMAGE.

Reported: 1985-10-18 (October 18, 1985) · Model years: 1986

NYLON FUEL LINES ON THE FUEL RETURN SIDE OF THE FUEL PRESSURE REGULATOR ASSEMBLY MAY CRACK. CONSEQUENCE OF DEFECT: FUEL LINE COULD LEAK AND, IF AN IGNITION SOURCE IS PRESENT, CREATE THE POTENTIAL FOR A FIRE.

Remedy: REPLACE NYLON FUEL HOSES WITH RUBBER HOSES.

Reported: 1987-09-04 (September 4, 1987) · Model years: 1986, 1987

SPRING LOCK FUEL LINE COUPLING MAY NOT BE PROPERLY ENGAGED.

Consequence: COUPLING COULD DISENGAGE DUE TO FUEL PRESSURE,VIBRATION, AND ENGINE MOVEMENTS; THIS WOULD CAUSE LOSS OF FUEL WHICH, INPRESENCE OF AN IGNITION SOURCE, CREATES A FIRE RISK.

Remedy: INSTALL RETAINER CLIPS OVER THE COUPLINGS TO PREVENT COUPLING SEPARATION AND FUEL LEAKAGE.

Reported: 1988-09-02 (September 2, 1988) · Model years: 1986

WIRING FOR THE POWER LUMBAR SEAT SYSTEM WAS ROUTED DIRECTLY BENEATH THE SEAT CUSHION SPRINGS AND MAY BE ABRADED BY THE SPRINGS.

Consequence: THIS COULD RESULT IN A SHORT CIRCUIT WHICH MAY CREATESUFFICIENT HEAT TO START A FIRE IN THE SEAT CUSHION PAD AND/OR TRIM COVER.

Remedy: INSTALL A FUSE WITHIN THE POWER LUMBAR ELECTRICAL CIRCUIT.

Reported: 1987-05-18 (May 18, 1987) · Model years: 1987

STICKERS CONCERNING HANDLING AND MANEUVERABILITY WHICH ARE AFFIXED TO DRIVERS SUN VISOR SLEEVES DO NOT MEET CRITERIA FOR PERMANENT ADHESION.

Consequence: VEHICLES DO NOT MEET FORMATS SPECIFIED BY PARTS 573 AND579 OF 49CFR.

Remedy: OWNERS WILL BE MAILED NEW SUN VISOR SLEEVES WITH ALL APPLICABLE DECAL INFORMATION PERMANENTLY AFFIXED.

Reported: 1987-05-26 (May 26, 1987) · Model years: 1987

THE BUCKLE PORTION OF THE SEAT BELT ASSEMBLY MAY NOT HAVE BEEN PROPERLY ANCHORED TO THE FLOOR.

Consequence: IF THIS CONDITION EXISTS, THE SEAT BELT ASSEMBLY WOULDNOT WITHSTAND A SUBSTANTIAL IMPACT LOAD AND WOULD BE A POTENTIAL FOR PERSONALINJURY.

Remedy: INSPECT AND MAKE PROPER INSTALLATION OF SEAT BELT AND BUCKLE ANCHOR BOLTS, IF NECESSARY.

Reported: 1987-09-04 (September 4, 1987) · Model years: 1987

WHEEL LUG NUT CONE ANGLES DO NOT MATCH LUG NUT SEATING ANGLES.

Consequence: NUTS COULD LOOSEN IN SERVICE CREATING POTENTIAL FORWHEELS TO SEPARATE FROM TRUCK.

Remedy: REPAIR TO PREVENT LOOSENING OF LUG NUTS.

Reported: 1987-09-04 (September 4, 1987) · Model years: 1988

TRUCKS WERE BUILT WITH INCORRECT REAR BRAKE ASSEMBLIES. CONSEQUENCE OF DEFECT: A TENDENCY FOR REAR BRAKE LOCKUP WOULD EXIST PARTICULARLY DURING HEAVY BRAKE APPLICAION WITH A LIGHTLY LOADED TRUCK. ALSO, INCREASED STOPPING DISTANCE WOULD BE REQUIRED IF THE BRAKE MODULATION (PUMPING THE BRAKES) IS USED TO CONTROL THE VEHICLE DURING A HARD BRAKE STOP.

Remedy: REPLACE REAR BRAKE ASSEMBLIES.

Reported: 1989-07-05 (July 5, 1989) · Model years: 1989

FRONT WHEEL BEARING ADJUSTING NUT RETAINING KEYS MAY BE MISSING FROM FRONT AXLE ASSEMBLIES, ALLOWING THE NUT TO LOOSEN.

Consequence: THIS COULD RESULT IN DETACHMENT OF THE WHEEL AND HUBASSEMBLY FROM THE AXLE, LOSS OF VEHICLE CONTROL, AND AN ACCIDENT.

Remedy: INSTALL RETAINING KEYS IN FRONT WHEEL HUB ASSEMBLIES WHERE MISSING.

Reported: 1989-12-22 (December 22, 1989) · Model years: 1990

THROTTLE LEVER MAY CONTACT THROTTLE BODY AIR INLET TUBE, WITH THE POTENTIAL FOR THROTTLE REMAINING OPEN FOLLOWING RELEASE OF THE ACCELERATOR PEDAL FROM THE FULL-THROTTLE POSTION IN TRUCKS WITH 4.0 L ENGINES.

Consequence: UNCONTROLLED ACCELERATION COULD CREATE LACK OF CONTROLAND CAUSE AN ACCIDENT.

Remedy: MANUFACTURER WILL REPLACE AIR INLET TUBE WITH NEWLY DESIGNED REPLACEMENT WITH AN INCREASED THROTTLE LEVER-TO-INLET TUBE CLEARANCE.

Reported: 1990-03-01 (March 1, 1990) · Model years: 1990

THROTTLE LEVER MAY CONTACT THROTTLE BODY AIR INLET TUBE, WITH POTENTIAL FOR THROTTLE REMAINING OPEN FOLLOWING RELEASE OF THE ACCELERATOR PEDAL.

Consequence: UNCONTROLLED ACCELERATION COULD CREATE LACK OF CONTROLAND CAUSE AN ACCIDENT.

Remedy: MANUFACTURER WILL REPLACE AIR INLET TUBE WITH NEWLY DESIGNED REPLACEMENT.

Reported: 1991-11-04 (November 4, 1991) · Model years: 1990, 1991

WHEN THE AUTOMATIC TRANSMISSION SHIFT LEVER IS PLACED IN THE PARK POSITION, THE PARK PAWL DOES NOT ALWAYS ABUT OR ENGAGE THE PARK GEAR.

Consequence: DRIVER MAY BELIEVE THE VEHICLE IS SAFELY ENGAGED IN PARKWHEN THE GEAR IS NOT TRULY ENGAGED. THIS CAN LEAD TO THE VEHICLE JUMPING OUT OFGEAR UNINTENTIONALLY, VEHICLE ROLLAWAY WHEN PARKED ON A SLOPED SURFACE, ANDINADVERTENT MOTION WHEN THE VEHICLE IS STARTED. ALL OF THESE CONDITIONS CANRESULT IN A VEHICLE ACCIDENT.

Remedy: REPAIR THE TRANSMISSION WITH A NEW PARK PAWL.

Reported: 1996-02-05 (February 5, 1996) · Model years: 1991, 1992, 1993, 1994

THE STUDS WHICH ATTACH THE BRAKE MASTER CYLINDER TO THE POWER BRAKE VACUUM BOOSTER ASSEMBLY CAN DEVELOP STRESS CORROSION CRACKING AFTER BEING OPERATED FOR AN EXTENDED PERIOD OF TIME IN THE SOUTHERN CALIFORNIA LOCATION.

Consequence: IF A CRACK OCCURS, IT COULD RESULT IN ONE OR BOTH STUDS FRACTURING. THE MASTER CYLINDER COULD THEN SEPARATE FROM THE VACUUM BOOSTER, WHEN THE BRAKES ARE APPLIED, PREVENTING THE SERVICE BRAKES FROM ACTIVATING INCREASING THE RISK OF A VEHICLE ACCIDENT.

Remedy: DEALERS WILL REPLACE THE POWER BRAKE VACUUM BOOSTER ASSEMBLY.

Reported: 1992-01-14 (January 14, 1992) · Model years: 1992

WATER CAN ENTER THE DOOR LATCH RELEASE CABLE. IF THE VEHICLE IS OPERATED IN BELOW FREEZING TEMPERATURES, THE WATER IN THE DOOR LATCH RELEASE CABLE CAN FREEZE AND CAUSE THE LATCH MECHANISM TO MALFUNCTION.

Consequence: THE MALFUNCTION OF THE DOOR LATCH RELEASE CAN RESULT INTHREE DIFFERENT PROBLEMS: 1) THE DOOR WILL NOT BE ABLE TO BE RELATCHED, 2) THEINSIDE DOOR HANDLE CAN BECOME INOPERATIVE, AND 3) THE DOOR COULD APPEAR TO BELATCHED WHEN IT IS NOT, ALLOWING THE DOOR TO OPEN UNEXPECTEDLY IF IT IS JARRED,AND INCREASING THE RISK OF INJURY TO THE ADJACENT SEAT OCCUPANT.

Remedy: REVISED DOOR RELEASE CABLES AND WATER SHIELDS WILL BE INSTALLED.

Reported: 1994-09-07 (September 7, 1994) · Model years: 1993, 1994

THE PARKING BRAKE CONTROL SELF-ADJUST PAWL DOES NOT LINE UP PROPERLY WITH THE SELF-ADJUST RACHET CAUSING THE PAWL TO SLIP OVER ONE OR MORE TEETH IN THE RACHET.

Consequence: WHEN THE ABOVE OCCURS, IT CAN RESULT IN PARKING BRAKE SYSTEM INEFFECTIVENESS. THE PARKING BRAKE WILL NOT HOLD THE VEHICLE, CAUSING THE VEHICLE TO ROLL FREELY, IF THE TRANSMISSION IS NOT LEFT IN GEAR.

Remedy: A WEDGE WILL BE INSTALLED WHICH WILL SERVE TO LOCK THE PARKING BRAKE SELF-ADJUST MECHANISM PAWL INTO ENGAGEMENT WITH THE RACHET. ALSO, OWNERS WILL BE ADVISED TO RELEASE AND REAPPLY THE PARKING BRAKE WHENEVER TOOTH SKIP OCCURS AND WILL BE REMINDED TO ALWAYS TURN OFF THE ENGINE AND LEAVE THE VEHICLE IN GEAR WHEN THE VEHICLE IS PARKED.

Reported: 1995-12-05 (December 5, 1995) · Model years: 1993, 1994

DURING EXTREME COLD, NORTHERN CLIMATE WINTER CONDITIONS, ICE CAN FORM IN THE THROTTLE BODY OF THE ENGINE CAUSING THE THROTTLE PLATE TO REMAIN IN THE HIGHWAY CRUISING POSITION AFTER THE ACCELERATOR IS RELEASED OR THE SPEED CONTROL IS DEACTIVATED.

Consequence: THE VEHICLE STOPPING DISTANCES CAN BE INCREASED POSSIBLY RESULTING IN AN ACCIDENT.

Remedy: DEALERS WILL REPLACE THE AIR INTAKE DUCT AND VALVE ASSEMBLY WITH REVISED UNITS.

Reported: 1994-06-13 (June 13, 1994) · Model years: 1994

THE FRONT FUEL LINES HAVE A SECTION OF FLEXIBLE HOSE THAT IS SUSCEPTIBLE TO CRACKING WHICH CAN ALLOW FUEL LEAKAGE.

Consequence: LEAKING FUEL CAN RESULT IN A FIRE WHEN EXPOSED TO A SOURCE OF IGNITION.

Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REPLACE THE FRONT FUEL LINE ASSEMBLY.

Reported: 2009-10-13 (October 13, 2009) · Model years: 1995, 1996, 1997, 2001, 2002, 2003

FORD IS RECALLING MODEL YEARS 1995-2003 WINDSTAR, 2000-2003 EXCURSION DIESEL, 1993-1997 AND 1999-2003 F-250 SD THROUGH F-550 SD DIESEL, 1992-2003 E-150 THROUGH E-550, 1995-2002 EXPLORER, 1997 AND 2002 MERCURY MOUNTAINEER, 1995-1997 AND 2001-2003 RANGER, AND 1994 F53 VEHICLES EQUIPPED WITH THE TEXAS INSTRUMENTS SPEED CONTROL DEACTIVATION SWITCH (SCDS). THE SCDS MAY LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Consequence: A VEHICLE FIRE COULD OCCUR WITH OR WITHOUT THE ENGINE RUNNING.

Remedy: FORD WILL NOTIFY OWNERS THAT DEALERS WILL INSTALL A FUSED WIRING HARNESS IN LINE WITH THE SCDS. ON 1999-2003 WINDSTAR VEHICLES WITH A LEAKING SCDS, DEALERS WILL ALSO INSPECT THE ABS CONTROL MODULE CONNECTOR AND REPAIR AS NECESSARY. REPAIRS WILL BE COMPLETED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON OCTOBER 27, 2009. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

Reported: 1996-08-29 (August 29, 1996) · Model years: 1996

THE CERTIFICATION LABELS ON THE INVOLVED VEHICLES HAS INCORRECT REAR TIRE INFLATION PRESSURE DESIGNATIONS. THIS DOES NOT COMPLY WITH FMVSS NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS."

Consequence: INCORRECT INFLATION PRESSURES COULD CAUSE PREMATURE WEAR OF THE REAR TIRES. .

Remedy: OWNERS WILL BE PROVIDED WITH CORRECT CERTIFICATION LABELS AND INSTRUCTIONS FOR INSTALLING THESE LABELS. DEALERS CAN INSTALL THIS LABEL IF THE OWNER SO DESIRES.

Reported: 2007-08-03 (August 3, 2007) · Model years: 1998, 1999, 2000, 2001, 2002

ON CERTAIN PICKUP TRUCKS, PASSENGER VEHICLES, SPORT UTILITY VEHICLES, AND MOTOR HOMES CHASSIS, THE SPEED CONTROL DEACTIVATION SWITCH MAY, UNDER CERTAIN CONDITIONS, LEAK INTERNALLY AND THEN OVERHEAT, SMOKE, OR BURN.

Consequence: THIS COULD RESULT IN AN UNDERHOOD FIRE.

Remedy: DEALERS WILL INSTALL A FUSED WIRING HARNESS. OWNERS OF THE PASSENGER CARS INCLUDED IN THIS CAMPAIGN WILL BE INSTRUCTED TO RETURN THEIR VEHICLES TO THEIR DEALERS TO HAVE THE SPEED CONTROL DEACTIVATION SWITCH DISCONNECTED AS AN INTERIM REPAIR. AS SOON AS REPAIR PARTS ARE AVAILABLE (EXPECTED OCTOBER 2007), OWNERS WILL BE INSTRUCTED TO RETURN TO THE DEALERS FOR INSTALLATION OF A FUSED WIRING HARNESS. THE RECALL BEGAN ON AUGUST 13, 2007, AND MAILING COMPLETED BY SEPTEMBER 19, 2007. OWNERS MAY CONTACT FORD AT 1-888-222-2751.

Reported: 1997-10-28 (October 28, 1997) · Model years: 1998

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS EQUIPPED WITH 4.0L ENGINES. THE FLEXIBLE SECTION OF THE CHASSIS MOUNTED FUEL LINE THAT CONNECTS TO THE ENGINE WAS ROUTED TOO CLOSE TO THE EXHAUST MANIFOLD. THE LINE COULD CONTACT THE MANIFOLD.

Consequence: THIS COULD POTENTIALLY RESULT IN DAMAGE TO THE FUEL LINE, OR IN SOME CASES, CAUSE A FUEL LEAK. FUEL LEAKAGE IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE.

Remedy: DEALERS WILL INSTALL AN ADDITIONAL CLIP TO HOLD THE FUEL LINE IN THE INTENDED DESIGN POSITION.

Reported: 1998-02-02 (February 2, 1998) · Model years: 1998

VEHICLE DESCRIPTION: LIGHT DUTY FOUR-WHEEL DRIVE PICKUP TRUCKS EQUIPPED WITH OFF-ROAD OPTION. THE TIRE AND RIM IDENTIFICATION INFORMATION IS INCORRECT ON THESE VEHICLES. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 120, "TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS."

Consequence: THE 16" TIRES COULD NOT BE INFLATED ON THE SPECIFIED 15X7.0J RIM.

Remedy: OWNERS WILL BE SENT A SAFETY CERTIFICAITON LABEL PARTIAL OVERLAY WHICH WILL CONTAIN THE CORRECT RIM SIZE, AND INSTRUCTIONS FOR AFFIXING THIS LABEL TO THE VEHICLE. IF AN OWNER SO DESIRES, THEIR FORD DEALER CAN INSTALL THE LABEL FOR THEM.

Reported: 1999-03-30 (March 30, 1999) · Model years: 1998, 1999

VEHICLE DESCRIPTION: CERTAIN 1997-1999 RHD EXPLORER EQUIPPED WITH 4.0L OHV/SOHC ENGINES AND CRUISE CONTROL BUILT FROM MAY 29, 1996 THROUGH MARCH 4, 1999; 1998-1999 EXPLORER/MOUNTAINEERS EQUIPPED WITH 4.0L OHV/SOHC OR 5.0L ENGINES OR 1998-1999 RANGERS EQUIPPED WITH 2.5L, 3.0L FFV/EFI OR 4.0L ENGINES AND CRUISE CONTROL BUILT FROM JANUARY 5, 1998 THROUGH MARCH 4, 1999; 1998-1999 MUSTANGS EQUIPPED WITH 3.8L, 4.6L 2-VALVE OR 4-VALVE ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; 1999 F250/F350/F450/F550 (OVER 8,500 LBS.) TRUCKS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999; AND 1999 F-53 STRIPPED CHASSIS EQUIPPED WITH 5.4L OR 6.8L ENGINES AND CRUISE CONTROL BUILT FROM MARCH 2, 1998 THROUGH MARCH 4, 1999. A CRUISE CONTROL CABLE CAN INTERFERE WITH THE SPEED CONTROL SERVO PULLEY AND NOT ALLOW THE THROTTLE TO RETURN TO IDLE WHEN DISENGAGING THE CRUISE CONTROL.

Consequence: IF THE CRUISE CONTROL IS USED AND THIS CONDITION IS PRESENT, A STUCK THROTTLE COULD RESULT, WHICH COULD POTENTIALLY RESULT IN A CRASH.

Remedy: DEALERS WILL REPLACE THE CRUISE CONTROL CABLES. AT THE PRESENT TIME, THE REPLACEMENT CABLES ARE NOT AVAILABLE. CUSTOMERS ARE BEING ADVISED NOT TO USE THE CRUISE CONTROL SYSTEM UNTIL A REPLACEMENT CAN BE MADE.

Reported: 1999-07-28 (July 28, 1999) · Model years: 1998, 1999

VEHICLE DESCRIPTION: ELECTRIC VEHICLES. THE TRANSAXLE MAY HAVE BEEN MANUFACTURED WITH THE PARK DETENT SPRING MISALIGNED. IF THE SPRING IS MISALIGNED, THE PARK MECHANISM MAY NOT ENGAGE WHEN THE SHIFT LEVER IS PLACED IN THE PARK POSITION.

Consequence: IF THE PARK MECHANISM DOES NOT ENGAGE AND THE VEHICLE OPERATOR HAS NOT APPLIED THE PARKING BRAKE, THE VEHICLE COULD ROLL FREE AS IF IN NEUTRAL.

Remedy: DEALERS WILL INSPECT THE TRANSAXLE AND ANY WITH MISALIGNED PARK DETENT SPRINGS WILL BE REPLACED.

Reported: 1998-09-01 (September 1, 1998) · Model years: 1999

VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS WITH 3.0L ENGINE. AN 'O'-RING SEAL IN THE FUEL INJECTION PULSE DAMPER TO FUEL RAIL JOINT COULD BE DAMAGED ALLOWING FUEL LEAKAGE.

Consequence: IN THE PRESENCE OF AN IGNITION SOURCE, A FIRE CAN RESULT FROM FUEL LEAKAGE.

Remedy: DEALERS WILL REPLACE THE PULSE DAMPER.

Reported: 2000-03-28 (March 28, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PICKUP TRUCKS EQUIPPED WITH 2.5L OHC ENGINES. ENGINE COOLANT CIRCULATION THROUGH THE HEATER CIRCUIT IS PREVENTED BECAUSE OF A PLUGGED HEATER RETURN TUBE (WATER PUMP INLET TUBE) AT THE WATER PUMP. THESE VEHICLES DO NOT COMPLY WITH THE INTENT OF FMVSS NO. 103, "WINDSHIELD DEFROSTING AND DEFOGGING SYSTEMS."

Consequence: AS A RESULT OF NO HEAT IN THE HEATER CIRCUIT, DEFROST PERFORMANCE IS COMPROMISED.

Remedy: DEALERS WILL REPLACE THE PLUGGED HEATER WATER RETURN TUBES.

Reported: 2000-08-18 (August 18, 2000) · Model years: 2000

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANT MAY NOT BE PROPERLY RESTRAINED.

Remedy: DEALERS WILL INSPECT THE DATE CODE ON CERTAIN SEAT BELT BUCKLES OF YOUR VEHICLE AND REPLACE ALL SEAT BELT BUCKLES THAT FALL WITHIN THE SUSPECT DATE CODE RANGE. OWNER NOTIFICATION BEGAN OCTOBER 26, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

Reported: 2000-11-28 (November 28, 2000) · Model years: 2001

VEHICLE DESCRIPTION: SPORT UTILITY VEHICLES WITH STEEL HOODS AND CERTAIN PICKUP TRUCKS EQUIPPED WITH SHEET MOLDING COMPOUND HOODS. A WIRE FORMED HOOD STRIKER COULD BE SUSCEPTIBLE TO FATIGUE FRACTURES. IF THE HOOD STRIKER FRACTURES, THE HOOD COULD FLY OPEN WHILE THE VEHICLE IS BEING DRIVEN.

Consequence: A HOOD FLY-UP WHILE THE VEHICLE IS BEING OPERATED COULD RESULT IN REDUCED DRIVER VISIBILITY.

Remedy: DEALERS WILL REPLACE THE HOOD STRIKER.

Reported: 2001-07-16 (July 16, 2001) · Model years: 2001

VEHICLE DESCRIPTION: PASSENGER AND SPORT UTILITY VEHICLES, PICKUP TRUCKS, AND MINIVANS. EQUIPPED WITH SEAT BELTS SUPPLIED BY TRW. IT IS POSSIBLE THAT THE DRIVER'S AND/OR FRONT PASSENGER'S OUTBOARD SEAT BELT BUCKLE MAY NOT FULLY LATCH. FORD CROWN VICTORIA BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01 MERCURY GRAND MARQUIS BUILT AT ST. THOMAS ASSEMBLY PLANT FROM 4/17/00 - 5/29/01. LINCOLN TOWN CARS BUILT AT WIXOM ASSEMBLY PLANT FROM 3/27/00 - 5/30/01. LINCOLN NAVIGATORS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01. FORD WINDSTARS BUILT AT OAKVILLE ASSEMBLY PLANT FROM 3/23/00 - 5/30/01. FORD RANGERS BUILT AT TWIN CITIES PLANT FROM 3/28/00 - 5/30/01, AND ALSO AT THE EDISON PLANT FROM 3/13/00 - 5/25/01. FORD F-150 TRUCK BUILT AT NORFOLK PLANT FROM 4/18/00 - 5/25/00; AT ONTARIO PLANT FROM 5/10/00 - 5/28/01; AT KANSAS CITY PLANT FROM 9/11/99 - 5/25/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/9/01. FORD SUPER DUTY F-250, F-350, F-450, AND F-550 TRUCKS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 5/27/01; AND AT CUAUTITLAN PLANT FROM 5/16/00 - 6/19/01. FORD EXCURSIONS BUILT AT KENTUCKY PLANT FROM 4/17/00 - 10/2/00. FORD EXPEDITIONS BUILT AT MICHIGAN TRUCK PLANT FROM 4/11/00 - 5/31/01.

Consequence: IN THE EVENT OF A CRASH, THE RESTRAINT SYSTEM MAY NOT PROVIDE ADEQUATE OCCUPANT PROTECTION, INCREASING THE RISK OF PERSONAL INJURY TO THE SEAT OCCUPANT.

Remedy: DEALERS WILL INSPECT THE FRONT OUTBOARD SEAT BELT BUCKLES AND IF THE BUCKLE FAILS THE INSPECTION PROCESS, IT WILL BE REPLACED. OWNER NOTIFICATION BEGAN JULY 25, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-866-436-7332.

Reported: 2002-02-04 (February 4, 2002) · Model years: 2002

ON SOME MANUAL TRANSMISSION TRUCKS EQUIPPED WITH THE FX4 PACKAGE, THE REAR AXLE DIFFERENTIAL CASE COULD FRACTURE UNDER A HIGH TORQUE EVENT SUCH AS WHEN CUSTOMERS ACCELERATE RAPIDLY FROM A STOP OR WHEN A SPINNING TIRE SUDDENLY GAINS TRACTION.

Consequence: DIFFERENTIAL FRACTURES COULD POTENTIALLY RESULT IN WHEEL LOCK-UP.

Remedy: DEALERS WILL REPLACE THE REAR AXLE ASSEMBLY. OWNER NOTIFICATION BEGAN MARCH 29, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT FORD AT 1-800-392-3673.

Reported: 2004-07-14 (July 14, 2004) · Model years: 2004

ON CERTAIN PICKUP TRUCKS, THE FRAME MAY HAVE A CENTER RAIL SECTION FLANGE THAT WAS NOT FORMED PROPERLY.

Consequence: IN THE EVENT OF A SIDE IMPACT CRASH, THE FRAME RAIL SCOULD PUNCTURE THE FUEL TANK, RESULTING IN A FUEL LEAK. FUEL LEAKAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.

Remedy: DEALERS WILL INSPECT THE FRAME TO DETERMINE WHETHER THE FRAME WAS INCORRECTLY MANUFACTURED. IF THERE IS A PROBLEM, THE VEHICLE WILL NOT BE REPAIRED. FORD AND THE DEALER WILL REPLACE THE VEHICLE. THE RECALL BEGAN ON JULY 19, 2004. OWNERS SHOULD CONTACT FORD AT 1-800-392-3673.

Reported: 2011-07-13 (July 13, 2011) · Model years: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011

FORD IS RECALLING CERTAIN MODEL YEAR 2011 RANGER TRUCKS BUILT FROM JANUARY 25, 2011, THROUGH APRIL 25, 2011 AT THE TWIN CITIES ASSEMBLY PLANT, AND SERVICE PARTS DISTRIBUTED TO DEALERS FOR CERTAIN 2004 THROUGH 2011 MODEL YEAR RANGER TRUCKS, 2002 THROUGH 2005 MODEL YEAR EXCURSION VEHICLES, AND 2002 THROUGH 2007 MODEL YEAR F-250, F-350, F-450, AND F-550 TRUCKS FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, "LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT." THE MULTI-FUNCTION SWITCH WAS SHIPPED WITH A SUBCOMPONENT (SLIDER) THAT MAY EXPERIENCE DEFORMATION. A MULTI-FUNCTION SWITCH WITH A DEFORMED SLIDER MAY MALFUNCTION CAUSING THE TURN SIGNAL, TAIL LIGHTS, HAZARD WARNING SIGNAL FLASHERS AND/OR BRAKE LIGHTS NOT TO ACTIVATE.

Consequence: NON-FUNCTIONING LIGHTS COULD INCREASE THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE SWITCHES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 15, 2011. OWNERS MAY CONTACT FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.

Reported: 2015-05-28 (May 28, 2015) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is recalling certain model year 2004-2006 Ranger trucks manufactured March 24, 2003, to May 4, 2006. The affected vehicles are equipped with a passenger side frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Ford will notify owners, and dealers will replace the front passenger air bag inflator, free of charge. The recall began on December 4, 2015. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 15S22. Note: This recall partially supersedes recall 14V-787.

Reported: 2016-01-25 (January 25, 2016) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is recalling certain model year 2004-2006 Ranger vehicles manufactured March 24, 2003, to May 4, 2006. Upon deployment of the driver side frontal air bag, excessive internal pressure may cause the inflator to rupture.

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Ford will notify owners, and dealers will replace the air bag inflators, free of charge. The recall began February 26, 2016. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S03. Note: This recall supersedes 14V-343 and only applies to Rangers manufactured in North America.

Reported: 2017-12-11 (December 11, 2017) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is superseding a previous recall for certain 2004-2006 Ford Ranger trucks to implement a final repair. Upon deployment of the driver side frontal air bag, excessive internal pressure may cause the inflator to rupture.

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the driver's frontal air bag inflator with an alternate inflator, free of charge. The recall began January 16, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S42. Note: This recall supersedes recall 16V-036 which was an interim repair. Vehicles that received a replacement air bag inflator under the previous campaign need to return to a dealer to have an alternate inflator installed.

Reported: 2017-12-11 (December 11, 2017) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is superseding a previous recall for certain 2004-2006 Ford Ranger trucks to implement a final repair. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.

Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants, potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger's frontal air bag inflator with an alternate inflator, free of charge. The recall began January 16, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S42. Note: This recall supersedes recall 15V322 which was an interim repair. Vehicles that received a replacement air bag inflator under the previous campaign need to return to a dealer to have an alternate inflator installed. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S42.

Reported: 2021-02-17 (February 17, 2021) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is recalling certain 2004-2006 Ranger vehicles that may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.

Reported: 2021-02-16 (February 16, 2021) · Model years: 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011

Ford Motor Company (Ford) is recalling certain 2005-2014 Mustang, 2004-2011 Ranger, 2009-2011 Mercury Milan, 2006 Ford GT, 2008-2012 Fusion, 2007-2010 Edge and Lincoln MKX, and 2009-2010 Lincoln MKZ vehicles. These vehicles may be equipped with a driver or passenger frontal air bag inflator used as a replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: In the event of a crash necessitating deployment of the frontal air bag, an inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Ford will notify owners, and dealers will inspect the driver and passenger air bag module, and replace either the module or the inflator, if necessary, free of charge. The recall began March 17, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S05.

Reported: 2023-02-24 (February 24, 2023) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is recalling certain 2004-2006 Ranger vehicles that received replacement front passenger air bag inflators under a previous recall. The replacement frontal passenger air bag inflators may have been installed incorrectly.

Consequence: An incorrectly installed inflator may not properly inflate the passenger air bag, increasing the risk of injury during a crash.

Remedy: Dealers will inspect and reinstall the front passenger air bag inflator, as necessary, free of charge. Owner notification letters were mailed April 5, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S08. This recall has been fully superseded by recall 23V-306.

Reported: 2023-04-28 (April 28, 2023) · Model years: 2004, 2005, 2006

Ford Motor Company (Ford) is recalling certain 2004-2006 Ranger vehicles that received replacement front passenger air bag inflators under a previous recall. The replacement front passenger air bag inflators may have been installed incorrectly.

Consequence: An incorrectly installed inflator may not properly inflate the passenger air bag, increasing the risk of injury during a crash.

Remedy: Dealers will inspect and reinstall the front passenger air bag inflator, as necessary, free of charge. Owner notification letters were mailed May 22, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S08. This recall expands and replaces previous recall number 23V-125.

Reported: 2005-11-09 (November 9, 2005) · Model years: 2006

ON CERTAIN TRUCKS, PASSENGER CARS AND SPORT UTILITY VEHICLES, THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN PRODUCED WITHOUT GREASE BEING APPLIED TO THE OUTPUT SHAFT GEAR.

Consequence: AFTER A PERIOD OF CONTINUOUS USE ON THE HIGH SPEED SETTING, LACK OF GREASE ON THE OUTPUT SHAFT GEAR MAY CAUSE THE GEAR TO DISTORT OR FRACTURE DURING OPERATION RESULTING IN A LOSS OF WIPER FUNCTION. INOPERATIVE WIPERS UNDER INCLEMENT WEATHER CONDITIONS COULD CAUSE A CRASH DUE TO IMPAIRED VISIBILITY.

Remedy: DEALERS WILL INSPECT THE WIPER MOTOR FOR THE PRESENCE OF GREASE AND GREASE THE WIPER MOTOR GEARS IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 22, 2005. OWNERS MAY CONTACT FORD AT 1-800-392-3673 OR LINCOLN/MERCURY AT 1-800-521-4140.

Reported: 2018-01-11 (January 11, 2018) · Model years: 2006

Ford Motor Company (Ford) is recalling certain 2006 Ford Ranger trucks. Ford is requesting owners NOT TO DRIVE these vehicles until they have been repaired. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to explode. On January 11, 2018, Ford Motor Company (Ford) notified NHTSA that they are recalling 2,700 model year 2006 Ranger vehicles built with passenger-side air bag inflators. As of February 9, 2018, Ford is expanding the recall to a total of 33,310 model year 2006 Ranger vehicles built with passenger-side air bag inflators. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to explode.

Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with sharp metal fragments striking the vehicle occupants, potentially resulting in serious injury or death.

Remedy: Ford will notify owners instructing them to not drive their vehicles, and dealers will replace the passenger side air bag inflator with an alternate inflator, free of charge. The recall for the original population began on January 16, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S02.

Reported: 2018-01-11 (January 11, 2018) · Model years: 2006

Ford Motor Company (Ford) is recalling certain 2006 Ford Ranger trucks. Ford is requesting owners NOT TO DRIVE these vehicles until they have been repaired. On January 11, 2018, Ford Motor Company (Ford) notified NHTSA that they are recalling 2,700 model year 2006 Ranger vehicles built with driver-side air bag inflators . As of February 9, 2018, Ford is expanding the recall to a total of 33,310 model year 2006 Ranger vehicles. Upon deployment of the driver side frontal air bag, excessive internal pressure may cause the inflator to explode.

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could explode with sharp metal fragments striking the vehicle occupants, potentially resulting in serious injury or death.

Remedy: Ford will notify owners instructing them to not drive their vehicles, and dealers will replace the front driver side air bag inflator with an alternate inflator, free of charge. The recall for the original population began on January 16, 2018. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 18S02.

Reported: 2016-05-31 (May 31, 2016) · Model years: 2007, 2008, 2009, 2010, 2011

Ford Motor Company (Ford) is recalling certain model year 2007-2011 Ford Ranger vehicles, 2006-2011 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2007-2010 Ford Edge, Lincoln MKX vehicles, 2005-2006 Ford GT vehicles, and 2005-2011 Ford Mustang vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain model year 2007-2008 Ford Ranger, Edge and Lincoln MKX vehicles, 2006-2008 Ford Fusion, Mercury Milan and Lincoln Zephyr/MKZ vehicles, 2005-2006 Ford GT vehicles and 2005-2008 Ford Mustang vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Any vehicle not included in "Zone A", or "Zone B" is not included in the safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Ford mailed interim letters informing owners that parts are not yet available on July 15, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.

Reported: 2017-01-10 (January 10, 2017) · Model years: 2007, 2008, 2009

Ford Motor Company (Ford) is recalling certain 2012 Ford Fusion and Mustang and Lincoln Zephyr and MKZ vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Ford is recalling certain 2009 Ford Ranger, Edge, Fusion and Mustang, Lincoln MKX, MKZ and Zephyr and Mercury Milan vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Ford is recalling certain 2007-2008 Ford Ranger, Edge and Lincoln MKX, 2006-2008 Ford Fusion, Mercury Milan, Lincoln Zephyr and MKZ, 2005-2008 Ford Mustang and 2005-2006 Ford GT vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Interim letters informing owners of the recall and that parts are not yet available began mailing March 1, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.

Reported: 2021-03-10 (March 10, 2021) · Model years: 2007, 2008, 2009, 2010, 2011

Ford Motor Company (Ford) is recalling certain 2007-2011 Ranger, 2006-2012 Fusion, Lincoln Zephyr, Lincoln MKZ, 2006-2011 Mercury Milan, 2007-2010 Ford Edge, and Lincoln MKX vehicles. The driver's side air bag inflator may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: Ford will notify owners, and dealers will replace the driver-side airbag inflator or module with an alternate one, free of charge. Owner notification letters were mailed on April 9, 2021 for the passenger side, and November 14, 2022 for the driver side. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S12.

Reported: 2009-02-03 (February 3, 2009) · Model years: 2009

FORD IS RECALLING 11,134 MY 2009 4X2 RANGER VEHICLES. SOME FRONT WHEEL SPINDLES WERE IMPROPERLY MANUFACTURED CREATING THE RISK THAT A SPINDLE MAY FRACTURE DURING THE NORMAL USEFUL LIFE OF THE TRUCK.

Consequence: IF A SPINDLE FRACTURES, THE WHEEL MAY SEPARATE FROM THE VEHICLE INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL REPLACE THE FRONT SPINDLE IF NECESSARY FREE OF CHARGE. THE RECALL BEGAN ON FEBRUARY 27, 2009. OWNERS MAY CONTACT FORD AT 1-866-436-7332.

Reported: 2018-01-11 (January 11, 2018) · Model years: 2009, 2010

Ford Motor Company (Ford) is recalling certain 2013 Ford Mustang vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2010 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2009 Ford Edge, Fusion, Mustang and Ranger, Lincoln MKX and Zephyr/MKZ, and Mercury Milan vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S01.

Reported: 2010-05-11 (May 11, 2010) · Model years: 2010

FORD IS RECALLING CERTAIN MODEL YEAR 2010 RANGER VEHICLES MANUFACTURED FROM JUNE 8, 2009 THROUGH FEBRUARY 2, 2010 EQUIPPED WITH MANUAL TRANSMISSION. IT IS POSSIBLE FOR THE PARKING BRAKE CABLE TO BECOME DISCONNECTED FROM THE RIGHT REAR ACTUATOR DURING COLD WEATHER. THIS MAY OCCUR WHEN THE PARKING BRAKE IS RELEASED IF WET PARKING BRAKE SHOES HAVE FROZEN IN THE APPLIED POSITION. IF THE RIGHT REAR PARKING BRAKE CABLE BECOMES DISCONNECTED, THE PEDAL WILL HAVE EXTENDED TRAVEL AND MAY NOT FULLY APPLY THE PARKING BRAKE.

Consequence: A MANUAL TRANSMISSION VEHICLE PARKED IN NEUTRAL WITHOUT A FULLY APPLIED PARKING BRAKE MAY HAVE UNINTENDED MOVEMENT WHICH MAY CAUSE A CRASH.

Remedy: DEALERS WILL INSTALL A REVISED RIGHT REAR PARKING BRAKE ACTUATOR TO PREVENT CABLE DISCONNECTION FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 21, 2010. OWNERS MAY CONTACT FORD AT 1-866-436-7332.

Reported: 2011-02-21 (February 21, 2011) · Model years: 2010

FORD IS RECALLING CERTAIN MODEL YEAR 2010 FORD RANGER TRUCKS MANUFACTURED FROM OCTOBER 15, 2009, THROUGH MAY19, 2010. THE ENGINE FUEL LINE IN THE AREA OF THE THROTTLE BODY SHIELD MAY NOT HAVE A PROTECTIVE CONVOLUTE (COVER) PROPERLY INSTALLED. IF THE PROTECTIVE CONVOLUTE ON THE FUEL LINE IS NOT ASSEMBLED IN THE PROPER POSITION, THE EDGE OF THE SHIELD MAY CONTACT THE FUEL LINE. OVER TIME THIS CONTACT MAY CHAFE THE FUEL LINE, RESULTING IN A FUEL ODOR AND A POTENTIAL FUEL LEAK.

Consequence: A SUFFICIENT FUEL LEAK IN THE PRESENCE OF AN IGNITION SOURCE MAY RESULT IN A FIRE.

Remedy: DEALERS WILL TRIM THE THROTTLE BODY SHIELD AWAY FROM THE FUEL LINE AND INSPECT THE FUEL LINE FOR WEAR, AND REPLACE THE LINE IF NECESSARY FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 4, 2011. OWNERS MAY CONTACT THE FORD MOTOR COMPANY CUSTOMER RELATIONSHIP CENTER AT 1-866-436-7332.

Reported: 2019-01-07 (January 7, 2019) · Model years: 2010, 2011

Ford Motor Company (Ford) is recalling certain 2014 Ford Mustang vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Ford is recalling certain 2011 Ford Ranger and Mercury Milan vehicles, 2011-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles and 2011-2014 Ford Mustang vehicles sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Ford is also recalling certain 2010 Ford Edge and Lincoln MKX vehicles, 2010-2011 Ford Ranger and Mercury Milan vehicles, 2010-2012 Ford Fusion and Lincoln Zephyr/MKZ vehicles, and 2010-2014 Ford Mustang vehicles sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicles until the repair has been performed. Ford will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 13, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall 19S01.

Reported: 2019-02-01 (February 1, 2019) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ranger vehicles equipped with 10-speed automatic transmissions. In some of these vehicles, the transmission shift lever can be moved from the "Park" position without the key in the starting system and without depressing the brake pedal. As a result, these vehicles fail to comply with Federal Motor Vehicle Safety Standard (FMVSS) number 114, "Theft Protection."

Consequence: If the vehicle can be shifted out of Park without the brake applied, the vehicle may unexpectedly move. Unintentional vehicle movement can increase the risk of injury or crash.

Remedy: Ford has notified owners, and dealers will inspect and repair the transmission floor shift selector interlock assembly, as necessary, free of charge. The recall began February 22, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19C02.

Reported: 2019-05-13 (May 13, 2019) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ranger vehicles. The fasteners that attach the transmission shifter cable bracket to the transmission may loosen allowing the transmission to be in a different gear than indicated by the gear shift lever position.

Consequence: If the gear shift lever position does not match the actual transmission gear, the vehicle may move in an unexpected direction. Additionally, despite selecting 'Park', if the parking brake is not applied before the vehicle is exited, the vehicle may roll. Either scenario increases the risk of crash or injury.

Remedy: Ford will notify owners, and dealers will inspect and tighten the transmission shift cable bracket fasteners as necessary, and verify the proper transmission shift operation, free of charge. The recall began July 1, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S15.

Reported: 2019-07-10 (July 10, 2019) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ford Ranger vehicles with a SuperCab body style. The front passenger seat belt may have been improperly assembled.

Consequence: Improperly assembled seat belts may not adequately restrain occupants in a crash, increasing their risk of injury.

Remedy: Ford will notify owners, and dealers will inspect and, if necessary, replace the right front seat belt assembly, free of charge. The recall began July 29, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S23.

Reported: 2019-10-10 (October 10, 2019) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ranger vehicles. The Heating, Ventilating and Air Conditioning (HVAC) blower motor may electrically short.

Consequence: An electrical short can increase the risk of a fire.

Remedy: Ford will notify owners, and dealers will inspect the HVAC blower motor production date, replacing it as necessary, free of charge. The recall began December 4, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S34.

Reported: 2019-11-21 (November 21, 2019) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ranger trucks. The inline electrical connector terminals for the rear lights may be misaligned or not properly seated, potentially causing the rear lights to function intermittently or not at all.

Consequence: Intermittent or inoperative tail lamps can result in loss of stop, turn, rear position, and reverse lamp functions, which reduces the vehicle's visibility and may not fully alert other drivers that the vehicle is braking, turning, or reversing, increasing the risk of crash.

Remedy: Ford will notify owners, and dealers will inspect the inline connector for loose terminals and replace the connectors, if necessary, free of charge. The recall began March 5, 2020. A renotification was sent on July 10, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S43.

Reported: 2020-03-09 (March 9, 2020) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2019 Ranger vehicles previously repaired under recall 19V-726. The service replacement Heating, Ventilating and Air Conditioning (HVAC) blower motor that was installed may have an improper clearance between an electrical terminal and the conductive base plate that may result in an resistive electrical short.

Consequence: A resistive electrical short increases the risk of a fire.

Remedy: Ford will notify owners, and dealers will inspect and replace the HVAC blower motor, as necessary, free of charge. The recall began April 6, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S12.

Reported: 2021-10-15 (October 15, 2021) · Model years: 2019, 2020, 2021

Ford Motor Company (Ford) is recalling certain 2019-2021 Ford Ranger Super Cab vehicles. The front passenger outboard seat belt may not have been assembled properly, allowing the seat belt to be misrouted. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 208, "Occupant Crash Protection" and 209, "Seat Belt Assemblies."

Consequence: A misrouted seat belt may not adequately restrain an occupant in a crash, increasing the risk of injury.

Remedy: Ford will provide owners with instructions to perform a preliminary inspection of their front seat belts. Owners that detect an issue with the driver's seat belt, are unsure of the results, or do not want to perform an inspection, should not drive their vehicles and contact a Ford dealership. Dealers will inspect the front row outboard seat belts and replace them, if necessary, free of charge. Interim owner notification letters were mailed on November 5, 2021. Owner notification letters were mailed December 22, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C25.

Reported: 2023-05-26 (May 26, 2023) · Model years: 2019, 2020, 2021, 2022, 2023

Ford Motor Company (Ford) is recalling certain 2022-2023 Bronco, 2023 Super Duty F-250, and 2019-2023 Ranger vehicles. The Tire and Loading Information (TREAD) label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."

Consequence: An overloaded vehicle increases the risk of a crash.

Remedy: Ford will mail a new TREAD label to install over the existing label, free of charge. Owners will also have the option to take their vehicle to a Ford or Lincoln dealer to have the new label installed, free of charge. Owner notification letters were mailed July 21, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23C18.

Reported: 2025-06-27 (June 27, 2025) · Model years: 2019, 2020, 2021, 2022, 2023

Ford Motor Company (Ford) is recalling certain 2018-2022 Transit Connect, 2019-2020 MKZ, MKX, Edge, Continental, F-150, Nautilus, Fusion, 2019-2023 Ranger, Mustang, 2020-2021 EcoSport, Expedition, Navigator, 2020-2022 Escape, F-250 SD, Corsair, 2020-2023 Aviator, Transit, 2020-2024 Explorer, 2021-2024 Bronco Sport, and 2022-2024 Maverick vehicles. A software error may cause the rearview camera to display a blank image, or the image may remain on the display after the backing event has ended.

Consequence: A rearview camera that displays a blank image can reduce the driver's view behind the vehicle. A rearview image that continues to be displayed after the vehicle is shifted out of reverse may distract the driver. Both of these situations can increase the risk of a crash.

Remedy: Dealers will update the rearview camera software, free of charge. Owner notification letters were mailed September 4, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S72.

Reported: 2025-09-03 (September 3, 2025) · Model years: 2019

Ford Motor Company (Ford) is recalling certain 2015-2019 Lincoln MKC, Mustang, F-350 SD, F-250 SD, F-450 SD, 2015-2017 Lincoln Navigator, Expedition, 2015-2018 Edge, Transit Connect, 2016-2019 F-550 SD, Transit, 2017-2019 Econoline, and 2019 Ranger vehicles. The rearview camera may display a distorted, inverted, or blank image when the vehicle is in reverse.

Consequence: A rearview camera that displays an inverted, distorted, or blank image can reduce the driver’s view behind the vehicle, increasing the risk of a crash.

Remedy: Dealers will inspect and replace the rearview camera as necessary, free of charge. Owner notification letters were mailed January 13, 2026. Ford owners will receive letters in phases, beginning January 2026 and June 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S89. This recall expands previous NHTSA recall number 25V270. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning September 8, 2025.

Reported: 2025-10-10 (October 10, 2025) · Model years: 2019, 2020, 2021, 2022, 2023, 2024

Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.

Consequence: An electrical short circuit can increase the risk of a fire.

Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.

Reported: 2020-04-03 (April 3, 2020) · Model years: 2020

Ford Motor Company (Ford) is recalling certain 2020 Ranger and F-150 vehicles equipped with 10-speed automatic transmissions and certain 2020 Expedition vehicles equipped with a "police" package. The transmission shift cable lock clip may not be fully seated, allowing the transmission to actually be in a different gear than the gear shift position selected by the driver.

Consequence: If the transmission selection does not match the indicated gear selection, and the parking brake is not applied, unintended vehicle movement can occur, increasing the risk of injury or crash.

Remedy: Ford will notify owners, and dealers will inspect and correct the shift cable locking clip installation, as necessary, free of charge. The recall began April 27, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S18.

Reported: 2020-09-23 (September 23, 2020) · Model years: 2020

Ford Motor Company (Ford) is recalling certain 2020 Ford F-150, F-250, F-350, F-450, F-550, Explorer, Mustang, Transit, Expedition, Escape, Ranger and Edge, and Lincoln Nautilus and Corsair vehicles. Due to a poor electrical connection, the rearview camera may intermittently display a blank or distorted image. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."

Consequence: Reduced rearward visibility can increase the risk of a crash.

Remedy: Ford will notify owners, and dealers will replace the rearview camera, free of charge. The recall began November 17, 2020. Remedy became available on February 1, 2021. Owner notification letters were mailed on February 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20C19.

Reported: 2021-09-30 (September 30, 2021) · Model years: 2020, 2021

Ford Motor Company (Ford) is recalling certain 2020-2021 Ranger Super Cab vehicles equipped with rear seats containing fixed head restraints. The fixed head restraints may interfere with proper installation of certain types of child seats. Additionally, the child seat may not attach properly to the lower-rear anchors. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 225, "Child Restraint Anchorage System."

Consequence: An improperly attached child seat can increase the risk of injury in a crash.

Remedy: Dealers will inspect the rear-lower child restraint anchorages for correct alignment and adjust as necessary. Separately, dealers will replace the non-removable head restraints with removable head restraints, free of charge. Interim owner notification letters were mailed on November 5, 2021. Owner notification letters were mailed on March 17, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21C24.

Reported: 2021-12-16 (December 16, 2021) · Model years: 2021

Ford Motor Company (Ford) is recalling certain 2021 Ranger and Bronco vehicles. The cruise control radar module was misaligned during production.

Consequence: A misaligned radar module may prevent the vehicle from maintaining a safe distance from other vehicles when adaptive cruise control is active. In addition, the automatic emergency braking (AEB) system may react slowly, or not react at all, during a pre-collision assist braking event. Any of these scenarios can increase the risk of a crash.

Remedy: Dealers will adjust the angle of the cruise control radar module, free of charge. Owner notification letters were mailed January 21, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S52.

Reported: 2022-06-24 (June 24, 2022) · Model years: 2022

Ford Motor Company (Ford) is recalling certain 2022 Bronco and Ranger vehicles. The windshield may not have been properly bonded to the vehicle, which could allow it to detach during a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 212, "Windshield Mounting."

Consequence: A windshield that separates from a vehicle during a crash can increase the risk of injury.

Remedy: Dealers will remove and reinstall the windshield, free of charge. Owner notification letters were mailed July 18, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22C12.

Reported: 2022-09-14 (September 14, 2022) · Model years: 2022

Ford Motor Company (Ford) is recalling certain 2022 Explorer and Ranger vehicles equipped with 2.3L engines. The fuel line may be loose due to improper tightening of the fuel line connection.

Consequence: An improperly tightened fuel line connection may result in a fuel leak, increasing the risk of fire.

Remedy: Ford will inspect and replace the fuel line assembly, if needed, free of charge. Owner notification letters were mailed September 29, 2022. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 22S60.

Reported: 2023-04-20 (April 20, 2023) · Model years: 2023

Ford Motor Company (Ford) is recalling certain 2023 Bronco and Ranger vehicles. The lug nuts on the driver's side wheels may have been improperly tightened.

Consequence: Loose lug nuts may result in wheel detachment while driving, increasing the risk of a crash.

Remedy: Owners are advised not to drive their vehicles until the remedy is completed. Dealers will inspect, and if necessary, retighten the lug nuts, free of charge. Owner notification letters were mailed May 2, 2023. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 23S17.

Reported: 2024-08-09 (August 9, 2024) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024 Ranger and 2024 Lincoln Nautilus vehicles. When closing the windows with the global closing feature, the windows may not automatically reverse after detecting an object. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."

Consequence: A closing window may exert excessive force by pinching a driver or passenger before retracting, increasing the risk of injury.

Remedy: Dealers will update the driver door module (DDM) and the passenger door module (PDM) software, free of charge. Owner notification letters were mailed September 13, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24C24.

Reported: 2024-10-16 (October 16, 2024) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024 Ranger, and 2024-2025 Bronco vehicles. The front upper control arm ball joint nut may not have been installed or tightened properly, allowing the front upper control arm to detach from the knuckle assembly.

Consequence: A detached control arm can cause a loss of vehicle steering and control, increasing the risk of a crash.

Remedy: Dealers will inspect and verify that the ball joint fastener is tightened properly. If a fastener is loose or missing, the dealer will replace the ball joint and knuckle assembly as necessary, free of charge. Owner notification letters were mailed on November 20, 2024. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 24S64.

Reported: 2024-11-08 (November 8, 2024) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024 Ranger vehicles. The fuel vapor line bracket may have insufficient clearance to the fuel vapor line, which can result in fuel vapor line damage that can lead to a fuel vapor leak.

Consequence: A fuel vapor leak in the presence of an ignition source can increase the risk of a fire.

Remedy: Dealers will inspect for a fuel vapor line bracket and install a tie strap to secure the fuel vapor line to the bracket, free of charge. Owner notification letters were mailed November 20, 2024. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S71.

Reported: 2025-03-14 (March 14, 2025) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024-2025 F-150, Bronco, 2024 Ranger, 2025 Mustang, Explorer, and Aviator vehicles. The transmission valve body may have been machined incorrectly, which can cause reverse gear failure, or unexpected forward movement in reverse or neutral gear.

Consequence: Unexpected vehicle movement increases the risk of a crash.

Remedy: Dealers will replace the transmission main control valve body, free of charge. Owner notification letters were mailed April 11, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S19.

Reported: 2025-04-11 (April 11, 2025) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024 Ranger and 2024 Lincoln Nautilus vehicles previously repaired incorrectly under recall number 24V-597. When closing the windows with the global closing feature, the windows may not automatically reverse after detecting an object. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 118, "Power-Operated Window Systems."

Consequence: A closing window may exert excessive force and pinch a driver or passenger before retracting, increasing the risk of injury.

Remedy: Dealers will update the driver door module (DDM) and the passenger door module (PDM) software, free of charge. Owner notification letters were mailed May 15, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C10.

Reported: 2025-05-09 (May 9, 2025) · Model years: 2024, 2025

Ford Motor Company (Ford) is recalling certain 2024-2025 Bronco and Ranger vehicles. The front upper control arm ball joint fastener may be missing or tightened improperly, allowing the front upper control arm to detach from the knuckle assembly.

Consequence: A detached control arm can cause a loss of vehicle steering and control, increasing the risk of a crash.

Remedy: Dealers will inspect and tighten, or replace the ball joint fastener as necessary, free of charge. Owner notification letters were mailed May 23, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S45.

Reported: 2025-05-09 (May 9, 2025) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2021-2024 Bronco, F-150, 2021-2024 Edge, 2022-2025 Escape, F-250, F-350, F-450, F-550, F-600, 2022-2024 Expedition, 2022-2025 Transit, 2021-2023 Mach-E, 2024 Ranger, Mustang, 2021-2023 Lincoln Nautilus, 2022-2024 Navigator, and 2023-2024 Corsair vehicles. A software error may cause the rearview camera image to delay, freeze, or not display when the vehicle is in reverse.

Consequence: A frozen or missing rearview camera image can reduce the driver's view behind the vehicle, increasing the risk of a crash.

Remedy: The accessory protocol interface module (APIM) software will be updated by a dealer or through an over-the-air update, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model and model years. Interim letters notifying owners of the safety risk were mailed on June 26, 2025. Additional letters will be mailed once the final remedy is available on each phase. Owner notification letters were sent on October 8, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S49.

Reported: 2025-08-22 (August 22, 2025) · Model years: 2024, 2025, 2026

Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger vehicles. The side curtain air bags may contact the B-Pillar inner reinforcements and tear during deployment. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 226, "Ejection Mitigation."

Consequence: Air bags that deploy improperly during a crash increase the risk of injury.

Remedy: Dealers will install protective shields, free of charge. Owner notification letters were mailed September 26, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C41.

Reported: 2025-09-11 (September 11, 2025) · Model years: 2024

Ford Motor Company (Ford) is recalling certain 2024 Bronco and Ranger vehicles. The bolts securing the high pressure fuel pump may not be tightened properly, which can result in a fuel leak.

Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.

Remedy: Dealers will replace the high pressure fuel pump mounting bolts, free of charge. Owner notification letters were mailed September 25, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S90.

Reported: 2026-02-20 (February 20, 2026) · Model years: 2024, 2025, 2026

Ford Motor Company (Ford) is recalling certain 2021-2026 F-150, 2022-2026 F-250 SD, F-350 SD, F-450 SD, F-550 SD, Maverick, 2024-2026 Ranger, 2023-2026 F-600 SD, 2022-2027 Lincoln Navigator, Expedition, and 2026 E-Transit vehicles. When towing a trailer, the integrated trailer module (ITRM) may lose communication with the vehicle, possibly causing a loss of brake and turn signal lights, or a loss of brake function. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 108, " Lamps, Reflective Devices, and Associated Equipment."

Consequence: Trailer lights or brakes that do not function can reduce the driver’s ability to control the trailer and decrease the trailers visibility to other road users, increasing the risk of a crash.

Remedy: The integrated trailer module software will be updated by a dealer, or through an over-the-air (OTA) update, free of charge. Owner notification letters were mailed March 25, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C10. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning March 17, 2026.

Reported: 2026-04-14 (April 14, 2026) · Model years: 2024, 2025, 2026

Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger vehicles. The sun visor or headliner wiring harnesses may be improperly positioned or have excessive tape thickness, which can result in damaged wires.

Consequence: Damaged wires can create an electrical short and cause a fire in the A-pillar area, increasing the risk of injury or a crash.

Remedy: Dealers will inspect the wiring for damage and update the body control module software. Damaged wiring harnesses will be replaced as necessary. All repairs will be performed free of charge. This will be a Phased campaign. Phase 1 will include 2025 model year vehicles. Owners will be notified by mail the week of 5/31/2026. Phase 2 will include 2026 model year vehicles and Phase 3 will include 2024 model year vehicles. Owners will be notified by mail the week of 6/29/2026 for Phase 2 and the week of 7/27/2026 for Phase 3. Interim letters, notifying owners of the safety risk, were mailed May 5, 2026. Additional letters will be sent once the remedy is available, anticipated in October 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S29. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on April 17, 2026.

Reported: 2026-04-28 (April 28, 2026) · Model years: 2024, 2025, 2026

Ford Motor Company (Ford) is recalling certain 2024-2026 Ranger and Bronco vehicles. The front seats may have a loose or dislodged seat frame height-adjust pivot bolt.

Consequence: A seat with a dislodged bolt may not properly restrain an occupant in a crash, increasing the risk of injury.

Remedy: Dealers will inspect and replace the pivot links and bolts as necessary, free of charge. Owner notification letters were mailed May 22, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford’s number for this recall is 26S30. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov beginning April 30, 2026.

Reported: 2025-05-09 (May 9, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Ranger and Bronco vehicles. The bolts that secure the driver's seat frame to the body may be loose or missing. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 207, "Seating Systems."

Consequence: A seat with loose or missing fasteners may not properly restrain an occupant during a crash, increasing the risk of injury.

Remedy: Dealers will inspect the seat fasteners and tighten or install new fasteners as necessary, free of charge. Owner notification letters were mailed May 23, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C16.

Reported: 2025-06-13 (June 13, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Ranger trucks. The instrument panel was not properly configured, preventing many of the the warning lights or gauges from properly displaying. This includes forward collision warnings, auto emergency braking, traction control, roll stability, and other gauges. The fuel gauge, distance to empty, and fuel economy may also not show accurately. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard numbers 101, "Control and Displays" and 126, "Electronic Stability Control Systems."

Consequence: An instrument panel that does not clearly display critical safety information increases the risk of a crash.

Remedy: Dealers will update the instrument panel software, free of charge. Owner notification letters were mailed August 29, 2025. Owners may contact Ford customer service at 1-866-436-7332. Fords number for this recall is 25C23.

Reported: 2025-07-25 (July 25, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of power brake assist.

Consequence: An unexpected loss of power brake assist while driving can extend stopping distance and increase the risk of a crash. Additionally, a loss of power brake assist while ADAS features are engaged can result in the vehicle not braking as expected, increasing the risk of a crash.

Remedy: The EBB module software will be updated over-the-air (OTA) or by a dealer, free of charge. Owner notification letters were mailed on August 22, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S77.

Reported: 2025-10-09 (October 9, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Ranger vehicles. The instrument panel top cover may prevent the passenger air bag from deploying as intended. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 208, "Occupant Crash Protection."

Consequence: An air bag that does not deploy as intended increases the risk of injury in a crash.

Remedy: Dealers will replace the instrument panel assembly, free of charge. Owner notification letters were mailed November 26, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C54. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.

Reported: 2025-10-10 (October 10, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Bronco and Ranger vehicles. During manufacturing, the windshield may not have been properly bonded to the vehicle, allowing it to detach in a crash. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 212, "Windshield Mounting."

Consequence: In the event of a crash, windshield detachment can increase the risk of injury.

Remedy: Dealers will remove and replace the windshield, free charge. Owner notification letters were mailed October 20, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25C52. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 14, 2025.

Reported: 2025-12-01 (December 1, 2025) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Lincoln Navigator, F-150, Expedition, Bronco, and Ranger vehicles. The Electronic Brake Booster (EBB) module may malfunction while driving or when the driver is utilizing an Advanced Driver Assistance System (ADAS) feature, resulting in a loss of power brake assist.

Consequence: An unexpected loss of power brake assist while driving can extend stopping distance and increase the risk of a crash. Additionally, a loss of power brake assist while ADAS features are engaged can result in the vehicle not braking as expected, increasing the risk of a crash.

Remedy: Dealers will replace the electronic brake booster, free of charge. Owner notification letters were mailed February 26, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SD4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on December 3, 2025.

Reported: 2026-03-03 (March 3, 2026) · Model years: 2025

Ford Motor Company (Ford) is recalling certain 2025 Ranger, Lincoln Nautilus, Mustang, Maverick, Explorer, Escape, Lincoln Corsair, Bronco Sport, and Bronco vehicles. The exhaust gas recirculation (EGR) valve may fail, resulting in an unexpected loss of drive power.

Consequence: An unexpected loss of drive power increases the risk of a crash.

Remedy: Dealers will replace the EGR valves, free of charge. Owner notification letters were mailed July 31, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S10. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on March 4, 2026.

Reported: 2026-05-27 (May 27, 2026) · Model years: 2025, 2026

Ford Motor Company (Ford) is recalling certain 2025-2026 Explorer, Ranger, and Bronco vehicles. The engine may fail, which can result in a loss of drive power.

Consequence: A sudden loss of drive power can increase the risk of a crash.

Remedy: Dealers will replace the engine long block, free of charge. Interim letters, notifying owners of the safety risk, were mailed June 5, 2026. Additional letters will be sent once the remedy is available, anticipated in November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S35. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 28, 2026.

Reported: 2026-05-26 (May 26, 2026) · Model years: 2026

Ford Motor Company (Ford) is recalling certain 2026 Ranger and Bronco vehicles. The vehicle specifications listed on the tire placard and safety certification labels may be incorrect, including the VIN, capacity weight, seating capacity, front and rear gross axle weight rating (GAWR), tire and rim dimensions, and recommended cold tire pressure. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims" and 49 CFR Part 567, "Certification."

Consequence: The incorrect tire size, tire pressures, and GAWR listed on the labels can allow the vehicle to be overloaded or have improperly inflated tires, increasing the risk of a crash.

Remedy: Dealers will inspect and if necessary, replace the certification and TREAD labels, free of charge. Owner notification letters were mailed June 3, 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C24. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on May 28, 2026.

Reported: 2026-08-25 (August 25, 2026) · Model years: 2026

Ford Motor Company (Ford) is recalling certain 2026 Explorer, Bronco, Bronco Sport, Mustang, and Ranger vehicles. The engine piston domes may have been manufactured incorrectly, which can result in piston dome failure and lead to a loss of drive power.

Consequence: An unexpected loss of drive power increases the risk of a crash.

Remedy: Dealers will inspect the engine pistons and replace the engine long block, if necessary, free of charge. Interim letters, notifying owners of the safety risk, were mailed September 3, 2026. Additional letters will be sent once the remedy is available, anticipated in December 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S61. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on August 28, 2026.

Reported: 2026-09-22 (September 22, 2026) · Model years: 2026

Ford Motor Company (Ford) is recalling certain 2026 Ranger vehicles equipped with a 10.1-inch center stack screen. The screen may lose power and fail to display the rearview camera image. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."

Consequence: A rearview camera image that does not display reduces the driver's view behind the vehicle, increasing the risk of a crash.

Remedy: The remedy is currently under development. Interim letters notifying owners of the safety risk are expected to be mailed October 5, 2026. Additional letters will be sent when the remedy is available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26C42. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on September 25, 2026.